Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

ADS data display window to plot simulation results in Cadence

Status
Not open for further replies.
R

Ryan64

Newbie level 3
Joined
Sep 24, 2016
Messages
3
Helped
0
Reputation
0
Reaction score
0
Trophy points
1
Activity points
31
Hi,
I work with cadence and I use GoldenGate instead Spectre for simulation. And I want to display the simulations results in the ads data display window to can write equations in the display window. But I can't open ads data display window from the Cadence Analog Design Environment ADE.
So, my question how to open or to have the ads data display window from the Cadence Analog Design Environment ADE?

Thanks for your help:wink:
 

You have three options as output data format.
(1) ds
(2) blk
(3) psf

Choose (1) for data display in ADS framework.
 
  • Like
Reactions: Ryan64

    R

    Ryan64

    Points: 2
    Helpful Answer Positive Rating
pancho_hideboo said:
You have three options as output data format.
(1) ds
(2) blk
(3) psf

Choose (1) for data display in ADS framework.
Click to expand...

Thank you for your response. But, where we can find the option setup to change the data display format.
 

Ryan64 said:
I work with cadence and I use GoldenGate instead Spectre for simulation.
Click to expand...
There is no tool whose name is cadence.
Use correct terminology.
https://www.edaboard.com/threads/354854/#10

Ryan64 said:
But I can't open ads data display window from the Cadence Analog Design Environment ADE.
Click to expand...
Answer the followings.

(1) What post processing environment do you use for Keysight GoldenGate Simulation ?
Cadence Wavescan ?
Cadence ViVa ?
Keysight qWave ?

I know you don't use Keysight ADS Data Display where data format is "ds".

(2) What version of GoldenGate do you use ?

Ryan64 said:
where we can find the option setup to change the data display format.
Click to expand...
You can set this "setup>envionment" menu in ADE or GDE.

If you can not find this, enter following in Cadence CIW.
Code: 
envSetVal("GoldenGate.envOpts" "resultTypes" 'toggle '(nil t nil))

Order is (blk, ds, psf).
 
Last edited:
  • Like
Reactions: Ryan64

    R

    Ryan64

    Points: 2
    Helpful Answer Positive Rating
Hi,
Thank you for the information about the tool name.

(1) for the post processing environment I have two option Cadence viewer and qWave, as shown in the figure below

fig1.png

(2) the version of GoldenGate is 201501-4-9-0

For the data display format, when I choose ".ds", as shown in the figure below, the simulation works well, but after the simulation I don't get the data display.

fig2.png

Thank again for your help
 

Ryan64 said:
For the data display format,
when I choose ".ds", as shown in the figure below,
the simulation works well,
but after the simulation I don't get the data display.
Click to expand...
It seems you have not installed Add-on Software "GoldenGate Tools".
https://edadocs.software.keysight.com/display/support/GoldenGate+Downloads

If you install "GoldenGate Tools", ADS Data Display is available from ADE.

If you can not install "GoldenGate Tools" but have ADS, launch ADS and open blank Data Display and select "*.ds" from GoldenGate.
 
  • Like
Reactions: Ryan64

    R

    Ryan64

    Points: 2
    Helpful Answer Positive Rating
Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top