+ Post New Thread
Results 1 to 10 of 10

4th December 2011, 12:43 #1
 Join Date
 Aug 2011
 Posts
 726
 Helped
 18 / 18
 Points
 4,101
 Level
 15
 Blog Entries
 1
Methods for measuring power consumed by a ciruit
What are the methods for measuring the current consumed by a circuit and out put in a LCD

4th December 2011, 20:21 #2
 Join Date
 Oct 2010
 Location
 Kolkata India
 Posts
 726
 Helped
 172 / 172
 Points
 4,828
 Level
 16
 Blog Entries
 9
Re: Methods for measuring power consumed by a ciruit
What is the current range?
1. measure the voltage drop across a resistor in series with the load  simple ohms law, a 1 ohm resistor will drop 1V for every amp of current. it's usual to use a smaller resistor and amplify the voltage drop with an opamp  this also allows you to reference the voltage to 0V (by using a differential opamp circuit).
Use ADC to convert > microcontroller>output to LCD
For idea:
 Post added at 00:51  Previous post was at 00:44 
https://www.edaboard.com/thread168925.htmlLast edited by papunblg; 4th December 2011 at 20:19.
Rajsekhar Nag
..
Knowledge Grows When Shared
1 members found this post helpful.

Advertisement

5th December 2011, 07:45 #3
 Join Date
 Aug 2011
 Posts
 726
 Helped
 18 / 18
 Points
 4,101
 Level
 15
 Blog Entries
 1
Re: Methods for measuring power consumed by a ciruit
inside a 10 x 7W LED

Advertisement

5th December 2011, 08:36 #4
 Join Date
 Apr 2011
 Location
 Minneapolis, Minnesota, USA
 Posts
 12,949
 Helped
 2580 / 2580
 Points
 52,947
 Level
 56
Re: Methods for measuring power consumed by a ciruit
LCD's use tiny amounts of current, compared to LED's.
See if you can spot any variation in the overall current draw when the display shows all 8's (all segments lit up), as compared to when few segments are lit up. That might give you a way to estimate what's going on in terms of power consumption.

Advertisement

7th December 2011, 12:11 #5
 Join Date
 Dec 2009
 Location
 INDIA
 Posts
 452
 Helped
 92 / 92
 Points
 3,947
 Level
 14
 Blog Entries
 1
Re: Methods for measuring power consumed by a ciruit
You can always measure the current at source (for total current withdrawn) or consumed at load (total current consumed), Your question is not very clear, do you mean methods to measure the current?
The road of life twists and turns and no two directions are ever the same. Yet our lessons come from the journey, not the destination. ~ Don Williams, Jr.

8th December 2011, 04:30 #6
 Join Date
 Aug 2011
 Posts
 726
 Helped
 18 / 18
 Points
 4,101
 Level
 15
 Blog Entries
 1
Re: Methods for measuring power consumed by a ciruit
My intention is to measure the current consumed by a series of LEDs ,
To measure the power by normal mode and that saved by PWM mode by these in series

9th December 2011, 06:21 #7
 Join Date
 Apr 2011
 Location
 Minneapolis, Minnesota, USA
 Posts
 12,949
 Helped
 2580 / 2580
 Points
 52,947
 Level
 56
Re: Methods for measuring power consumed by a ciruit
I think you'll need to use this method:
Measure the voltage across your switching device while it's conducting.
Also measure current through the switching device while it's conducting. This may not be easy. If you have an oscilloscope then put a lowohm resistor inline and measure voltage across it.
Multiply V * A.
This will give you instantaneous watts wasted as heat through the device.
Multiply by your duty cycle. This will give you average watts wasted as heat.
Now you will calculate the theoretical waste if you used a linear resistive method to drop voltage.
You know the average applied voltage on the LED's, and the average current going through them. You also know your supply voltage. From these figures you can calculate what amount of power you would have been wasting.

9th December 2011, 07:55 #8
 Join Date
 Dec 2011
 Posts
 11
 Helped
 0 / 0
 Points
 217
 Level
 2
Re: Methods for measuring power consumed by a ciruit
I agree with your post sir,
:D
I want to ask how to make characters at row 2 in LCD sir? how its program?
visit my site also ELECTRONICS IS FUN

Advertisement

22nd January 2012, 16:21 #9
 Join Date
 Aug 2011
 Posts
 726
 Helped
 18 / 18
 Points
 4,101
 Level
 15
 Blog Entries
 1
Re: Methods for measuring power consumed by a ciruit
I dont want accuracy in the values we get, I want to calculate just the rough value in power we saved.
Btw, any PIC based project available for this ?

23rd January 2012, 06:29 #10
 Join Date
 Oct 2010
 Location
 Kolkata India
 Posts
 726
 Helped
 172 / 172
 Points
 4,828
 Level
 16
 Blog Entries
 9
Re: Methods for measuring power consumed by a ciruit
Pic16F876A(for example) contains inbuilt ADC. So the circuit will be simple as there is no external ADC in this case. Search this forum.
Rajsekhar Nag
..
Knowledge Grows When Shared
+ Post New Thread
Please login