Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

error in ads" Error detected by hpeesofsim during netli

Status
Not open for further replies.
L

layan

Member level 1
Joined
Nov 13, 2009
Messages
39
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,286
Activity points
1,501
error in ads

hi
How can I solve the following error in ads?

" Error detected by hpeesofsim during netlist parsing.
Unable to locate library "ckt" "
plz help me
thanks
 

error in ads

This may be related to design kit installation.
We need screen shots of error message, schematics etc. to understand the problem.
 

    L

    layan

    Points: 2
    Helpful Answer Positive Rating
Re: error in ads

yes but design kit installation is automatically
What should I do?

Added after 14 minutes:

hi
this is the shematic of the circuit and Avago_MGA_665P8_011009 relative files
thanks
 

Re: error in ads

i dont know where is the problem:(
 

Re: error in ads

You did nothing wrong.
The problem is with ADS model of MGA_665P8 device which may work with lower version of ADS may be ADS 2002 or ADS 2006 etc.
Why don't you use S-para data than model?
I checked the same with Avago site.

Added after 1 minutes:

you can use these files
 

    L

    layan

    Points: 2
    Helpful Answer Positive Rating
error in ads

again thanks:)
yes thats right ,it was for ads2003!!
i downloaded these files(s2p files) from avago.
but how can i use them with design kit installation?
Oh how I know ads? %)
 

error in ads

You do not require design kit.
You can set the design as shown in Fig 3 of your LNA project pdf.
 

    L

    layan

    Points: 2
    Helpful Answer Positive Rating
error in ads

oh but i need the last shematic of the pdf file
is there any way to have that?

Added after 10 minutes:

;(
 

Re: error in ads

If you go to ADS to the palette Data Items, you can select the S parameters needed for your simulations.
I include a couple of snapshots for your simulation, I hope they help.
 

    L

    layan

    Points: 2
    Helpful Answer Positive Rating
Re: error in ads

If you go to ADS to the palette Data Items, you can select the S parameters needed for your simulations.
I include a couple of snapshots for your simulation, I hope they help.
 

    L

    layan

    Points: 2
    Helpful Answer Positive Rating
Re: error in ads

dear fabrilf
i will try it soon
thanks alot ;)

Added after 19 minutes:

again hi
i tried it,here is its shematic
where is the errrrrorr:(
plzzzzz
 

error in ads

I'm really disappointed >;(
with installing MGA_665P8 in designkit for pj2 ,the first circuit (pj1) that had worked correctly before, became damage
now both of them Do not work ;'(
 

error in ads

oh kspalla How good u returned
plz help i will tried it

Added after 16 minutes:

sorry but it dosent work too,also when i open the ads ,at first it gives this error
"(C:\ADS2008\adsptolemy\ael\Avago_MGA_665P8_011009_encode_def.ael line 3, column 16 in dereference) Avago_MGA_665P8_011009_PATH
variable undefined
C:\ADS2008\adsptolemy\ael\Avago_MGA_665P8_011009_encode_def.atf
compiled AEL file not loaded"

i think my ads is broking
How can I sayyy to ads that I Have been deterred
and i want to delete allll files of avagomga665
 

Re: error in ads

In ADS main window you will find design kit-->setup design kits-->select the Avago MGA design kit >select cut-->apply and ok.
Restart ADS
 

    L

    layan

    Points: 2
    Helpful Answer Positive Rating
error in ads

Thanks All
I was finally successful to run the project in ADS.of course after installing ADS again :)
 

Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top