Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Printed Inductor (PLANAR INDUCTOR)

Status
Not open for further replies.

tiger2000

Junior Member level 1
Joined
May 28, 2001
Messages
18
Helped
0
Reputation
0
Reaction score
0
Trophy points
1,281
Activity points
58
planar inductor pcb

Can anyone tell me where I can find any writing or formula or equation about
PLANAR INDUCTORs ?
I have a pcb with a planar inductor and I want to calculate the inductance of it.
the PCB is single Layer and the shape of it is like this :
_______
_______|
|_______
_______|

Can anyone Help me?
Thanks.
 

planar inductor calculator

hi
check ieee circuits and systems magazine.
 

inductor planar

How can I achieve the IEEE and magazine ?
 

pcb inductor calculation

check your next university library ?
 

inductor planar calculator

Hi
If there are not too many of printed inductances you can measure precisely and send dimensions of each, and also type of the substrate, I can recalculate it in nH. I have no better idea in this moment, except to advice you yo spend lot of time and learn to use some of sophisticated programs for that purrpose.
Best regards
DD
 

Attachments

  • pwm1.gif
    pwm1.gif
    11.5 KB · Views: 143

printed planar inductor

give me the spec
i 'll simulate it for you and for free
 

planar pcb inductor

Serpentine trace is an inductance reducing geometry; the inductance is less than an equal length of straight wire!


Sun Microsystems engineering paper:
https://www.sun.com/research/techrep/2000/smli_tr-2000-92.pdf

_________________
Best regards,

Tanuki

<font size=-1>[ This Message was edited by: tanuki on 2001-07-30 13:41 ]</font>
 

inductor planar calculate

Tanuki,

You are correct, kind of, however it is very geometry dependant, as for the original poster, I've seen, somewhere on filemanager a PCB inductor calculator, I'm not too sure that this will work on a single sided board, with out a reference plane.

Skip
 

pcb inductor calculator

kaazemin,

What sort of application is this PCB used in?

Is it possible that the serpentine section is a antenna?

Otherwise a serpentine trace on single sided PCB makes little sense.

opps... almost forgot your IEEE question.

https://www.ieee.org/

Membership is open.
_________________
Best regards,

Tanuki

<font size=-1>[ This Message was edited by: tanuki on 2001-07-29 15:56 ]</font>
 

calculating planar inductor

I put a word document in my personal folder here on elektroda that may interest you.

On Filemanger #1
path: /Tanuki/Inductance
File: InductanceOfWire.doc
 

planar inductors on pcb calculation

i need a good cad for this
also but havent found a resonable one yet
 

Attachments

  • inverter.JPG
    inverter.JPG
    29 KB · Views: 106
  • ceamp.JPG
    ceamp.JPG
    58.6 KB · Views: 105
  • phase shifter.JPG
    phase shifter.JPG
    98 KB · Views: 110

inductor serpentine traces

is there any program to calculate it
 

Hi

I recall using PHILLIPS planar transformers design tools some time ago ..
Check them out!
 

Status
Not open for further replies.

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top