Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Search results

  1. N

    Banked and Unbanked Flash and Paged and Unpaged RAM

    Hi guys, Plz some body explain what is difference between Banked Flash and Non-banked flash. What is difference between Paged RAM and unpaged RAM. Regards V. Naresh Kumar
  2. N

    PCB Trace Width for 63A current carrying net

    HI, Thanks to karesz and zorx for giving valuable suggestions. Regards V. Naresh Kumar
  3. N

    PCB Trace Width for 63A current carrying net

    Dear All, In my project I am designing the 20A,14.3V forward converter. After calculations the peak current of converter 63A. Please let me know how to calculate the trace width for 63A current carrying net. Trace width calculators are available in internet, but all calculators maximum current...
  4. N

    Filter Design (Power Supply Filter Design)

    FVM, thanks for your reply, please can give some information about how to calculate the output capacitnce of rectifier circuit. Regards V. Naresh Kumar
  5. N

    Filter Design (Power Supply Filter Design)

    I require following information 1. Inductor calculation 2. Capacitor calculation 3. Ripple Regards V. Naresh Kumar
  6. N

    What do you wish to know? How to calculate cut-off frequency

    Dear fcfusion, I want know inductor and capacitor value calculation for forward converter. The operating frequency of forward converter is 24KHz. Regards V. Naresh Kumar
  7. N

    Filter Design (Power Supply Filter Design)

    Hi everybody, Normally in Forward converter at the output side LC filter is used. In attached document schematic of Forward Converter is used. In that LC filter is used at the output side. Please can any body explain how to design output LC filter. Regards V. Naresh Kumar
  8. N

    How to design the Filter

    Hi everybody, I have to design a filter to smooth the output inverter bridge output. The attached document shows sample circuit. In that sample circuit LN filter is used to smooth the PWM ouput to sine wave. Please some body explain how to design the LN filter. Regards V. Naresh Kumar
  9. N

    what is the use of delimiters in Control Area Network (CAN)

    Re: what is the use of delimiters in Control Area Network (C thanks for your reply microkernal There is acknowledgment slot to ack the receiver. With the addition to this ack slot there is another slot is there i.e. ACKDELIMITER. I want know what is use of ACKDELIMITER. Regards V. Naresh Kumar
  10. N

    what is the use of delimiters in Control Area Network (CAN)

    In the CAN there are two delimiters (ACK and CRC). Please can any body explains the what are uses of delimiters in the CAN. Regards V. Naresh Kumar
  11. N

    Cannot open include file "timescale.v, i2c_master_defin

    Re: Questasim simulator - error explain needed Thanks prashanth. Regards V. Naresh Kumar
  12. N

    Push-pull Boost converter

    Please any body give the design details about push pull configuration boost converter. Which type of transformer is used in this configuration. How to design this transformer. Please suggest any reference designs of push pull converter. Regards V. Naresh Kumar
  13. N

    Cannot open include file "timescale.v, i2c_master_defin

    Dear All. When I am simulating the Verilog project (with "include files" in the project) in Questasim simulator, I am getting the following Error Error: E:/i2c/trunk/rtl/verilog/i2c_master_bit_ctrl.v(138): Cannot open `include file "timescale.v". ** Error...
  14. N

    What is Error Active Station and Error passive Station

    Dear All, Please some body explain what are Error Active station and Error passive station in the Controller Area Network. Regards V. Naresh Kumar
  15. N

    What is the relation between infrared pulses and 38KHz frequency?

    Hi every body, I want use TSOP34838 as Infrared Detector. When I gone through the data sheet I didn't get the what is 38KHz carrier frequency in the data sheet. Normally the Infrared data is in type of pulses. Please some one explain what is the relation between infrared pulses and 38KHz...
  16. N

    I2C device addressing - why 4 MSB are fixed?

    I2C device addressing Hi, In I2C compliant devices why 4 Most significant bits are fixed. Example All EEPROMs address start with 1010 and next three bits are A2A1A0. I am assuming to reduce the address decoding logic. Is there is any specific reason. Regards V. Naresh Kumar
  17. N

    How to calculate distance between two tracks

    Hi guys, How to calculate distance between two tracks in the PCB. The tracks carrying either power or signals in PCB. Regards V. Naresh Kumar
  18. N

    Non linear operation of an OP-AMP used as a non-inverting amplifier

    Re: Op AMP Non linearity thanks FVM, If VCC is connected to 5V, my problem may solve. Regards V. Naresh Kumar
  19. N

    Non linear operation of an OP-AMP used as a non-inverting amplifier

    Re: Op AMP Non linearity Dear Lvw I updated the my schematic. Now it should work as a non-inverting amplifier. Input to non-inverting pin (IN+) is voltage across R19. IN- pin is ground through resistor network. My application is current sensing circuit. Regards V. Naresh Kumar
  20. N

    Non linear operation of an OP-AMP used as a non-inverting amplifier

    Re: Op AMP Non linearity Dear FVM, Thanks for your reply, I updated my schematic. According to updated schematic when 4-6 current flows through the resistor R19 the output value is 1.16(200V offset) to 1.64. When increases beyond the 6A the output is always 1.75V. I could not understand...

Part and Inventory Search

Top