Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Search results

  1. V

    no solder mask in pcb board

    Hi, I dont want to use a solder mask in a proto board that i am designing. So if I exclude the solder mask layer when export the layout to a gerber/dxf file, will it ensure that no solder mask layer is used? Thank you.
  2. V

    post parasitic extraction netlist

    I was wondering if someone could provide a comparison of what a pre extraction netlist and a post extraction netlist (with just RC extraction) in terms of the number of parasitic elements that are present in the post-netlist. Using a certain foundry, we found that the post-netlist had several...
  3. V

    current consumption for a crystal driver circuit

    How low can we get the current consumption for a crystal driver circuit to be? The frequencies of interest are in the range of 10-30kHz. Thank you in advance.
  4. V

    4 pin SMT packaging costs

    How much does a 4 pin SMT package costs in large volume (10 to 100M+)? If anyone knows any packaging vendor, please let me know.
  5. V

    Pros and cons of TSMC and MOSIS companies

    We are going to do two MPWs before engineering lots. What we found was that support from TSMC could be a lot better - even simple questions can take some time. So we are now considering going from TSMC to MOSIS for the MPW for this reason - can anyone comment on the pros and cons of each company...
  6. V

    RC vs RCLK extraction for 0.25u, 0.18u

    I wanted to get some thoughts on the impact of parasitics using RC and RCLK extraction for 0.25u and 0.18u. For 65nm, it seems RC extraction alone could be as much as 20% off of actual silicon performance and here RCLK extraction is preferred. But something tells me that for larger geometries...
  7. V

    recommended pad spacing for rfic ciruits

    We are designing a chip(this is a test chip) for the 900MHz. Is there a recommended pad spacing especially with respect to packaging considerations? Thank you in advance
  8. V

    Guard rings around individual transistors or whole circuit?

    Guardrings Generally for RF circuits such as LNA's mixers etc, is it recommended to use guard rings around individual transistors used in these circuits vs. guardrings around the whole circuit?
  9. V

    testing low power VCOs, 50 ohm line on a board

    We have designed a low power VCO and to test it we are bringing out the VCO outputs to be connected to 50 ohm line on a board. We cannot match the VCO output nodes to 50 ohms since this would be too much of a load on the VCO and can affect its frequency and amplitude. So we thought we could...
  10. V

    Port to Port Isolation for Mixer

    I was doing simulations on a fully balanced Gilbert Gain mixer - the LO signal is of amplitude 500mV and wanted to see how much of the LO signal leaks on to the RF port. What I found was that there was very little contribution at LO on the RF port but there was a huge component at 2LO on the...
  11. V

    Cadence spectre phase noise plots for oscillators

    Phase noise plots for oscillators using Cadence spectre (PSS+PNoise) in dBc/Hz show noise values greater than 0 at close in frequencies to the carrier (including several plots in their user guide) How is this possible?
  12. V

    Integer N PLL - lock times

    I am trying to design an integer n pll for 915MHz with a channel spacing of 100kHz. I wanted to get a sense of what are possible lock times possible. Is a lock time of say 100us feasible at all? Thank you in advance

Part and Inventory Search

Top