Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Search results

  1. M

    FDT434P pspice simulation model

    I imported the model into the schematic, I renamed the component to FDT434P, but when I tried to run the project, it didn't work, because it didn't find the model.
  2. M

    FDT434P pspice simulation model

    Hi, I have to do a simulation in LTSpice, and unfortunately I don't have a simulation model for FDT434P. On the fairchild web page there is a simulation model, but it was the extension .mod https://www.fairchildsemi.com/pf/FD/FDT434P.html Could you help me please with a simulation model for...
  3. M

    Alternative for MCP9510

    Hi, I have to do a redesign, and I have to replace MCP9510 component with a AEC one. Could you recommend me some automotive alternatives? Thank you.
  4. M

    help with code for rfPIC12F675

    Thanks, it looks similar to mine.
  5. M

    help with code for rfPIC12F675

    this is the remote control schematic:
  6. M

    help with code for rfPIC12F675

    I started to write the software for the transmitter board, but unfortunately it doesn't work. Could you help me please to fix it? Please find attached my C code: #include <htc.h> #include <pic.h> #include <picrf675f.h> // Internal registers configuration /* Data Memory Code Protection...
  7. M

    Anyone use Microchip rfPIC12F675K chip for remote control?

    Hi, I use also rfPIC12F675F on my project. Could you post please your code?
  8. M

    help with code for rfPIC12F675

    Could you give me please a "Hello World" example? For instance, if I press the button from Tx board, the LED from Rx board turns on.
  9. M

    help with code for rfPIC12F675

    Hi, Could you help me please with an example of C code for rfPIC12F675? It is my first RF application. The application is going to work at 433MHZ, ASK mode. Thank you.
  10. M

    PCB integrated antenna

    Hi, I am pretty new in the RF domain. The topic of my actual project is to design a remote control working at 433MHz. I made the schematics, and now I have to do the layout. The problem is, that I have to integrate the antenna in the PCB. I saw some examples of loop antenna on the PCB, but for...
  11. M

    433Mhz remote control circuit help

    Hi, I have to develop a wireless remote control on 433Mhz. There are some mechanical requirements regarding the dimensions of the PCB, it should be similar with a car remote door opener. The power supply is a coin battery of 3V, type CR2032. It has 3 buttons with which it can control 3...
  12. M

    how to drive an linear actuator

    I have no information about the gate weight at this moment. The gate is intended to open horizontally. From the information that I have the actuator will be connected with screws to the gate, and the control ECU will be put on one of the gate's pillar. It will be a RF system on 433Mhz...
  13. M

    how to drive an linear actuator

    Hi, here is the type of the linear actuator that I intend to use for a gate opener application: https://uk.rs-online.com/web/p/electric-linear-actuators/7643474/ First of all, is it ok? Or do you suggest me something else? Thank you.
  14. M

    how to drive an linear actuator

    It is a DC Motor, supplied at 12V.
  15. M

    how to drive an linear actuator

    Hi, I have to drive a linear actuator on my project wit a PIC18F2620. I have never worked with motors. Could you give me please some pieces of advise how to control it? Thank you.
  16. M

    output the CLK on an external mcu pin

    I found that I have to set the OPT bit from the FLASH_CR2 register in order to have access to option bytes, but how to set AFR2, I haven't found yet.
  17. M

    output the CLK on an external mcu pin

    I prefer to use the Reference Manual.
  18. M

    output the CLK on an external mcu pin

    https://www.st.com/web/catalog/mmc/FM141/SC1244/SS1010/LN1571/PF251553?s_searchtype=partnumber and the STM8S Reference Manual **broken link removed**
  19. M

    output the CLK on an external mcu pin

    Hi, I use on my project a STM8S207K8 mcu from ST, I configured the internal oscillator, HSI to work at 16Mhz. I use IAR embedded workbench. I want to output the CLK signal on an external CCO pin. Could you help me please how to do it? Since now I haven't work with STM8S mcus. Thank you in advance.
  20. M

    STM8 microcontroller programming help

    I installed the StVisualDeveloper, I wrote a "Hello World" program, and when I compiled it, I got an error. Could somebody help me to fix the Compiler? Thank you in advance.

Part and Inventory Search

Top