Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Search results

  1. G

    Help needed for operating Servo Motor.

    Dear All, I have a servo motor. I am unable to recognize it as I don't have any of it's data. Couldn't find details of this motor on internet too. Kindly help me in following questions. Is it a single phase or three phase motor ? Output Power mentioned on motor is 500W. What are the...
  2. G

    ICs for Isolated 24 to 48V 3Amp Boost Converter

    Dear Members, I want to design 24 to -48V 3 Amp Isolated Switch mode Boost converter. I am searching ICs to design. Kindly suggest some ICs. Thanks in advance.
  3. G

    How to design a smps based battery charger?

    Re: smps based battery charger I've no issues in redesigning whole thing. If it is a diode kindly let me know it's part number as it contains three pins used for different purposes.
  4. G

    How to design a smps based battery charger?

    Re: smps based battery charger What is the part number of the component at E$23 ? In PCB and Parts list only 40V/30A is written.
  5. G

    Smart and cost effective 12-V 160 AH lead acid battery charger

    What is the part number of the component at E$23 ? In PCB and Parts list only 40V/30A is written.
  6. G

    Smart and cost effective 12-V 160 AH lead acid battery charger

    We can mutually fix bugs by discussing here if you want.
  7. G

    How to design a smps based battery charger?

    we can fix mutually bugs by discussing here too.
  8. G

    How to design a smps based battery charger?

    Dear Amjad Ali, Can you share schematic of this charger ? Thank You. Regards, Gapoo
  9. G

    Smart and cost effective 12-V 160 AH lead acid battery charger

    Dear kindly show the schematic of your charger. I have following queries. 1) Are you sure that diode at E$25 is 1N4148 ? 2) What is the part number of the MOSFET at E$23 ? 3) Path of feedback is very long, will it effect the performance ? Thank You. Regards, Gapoo.
  10. G

    HC-09 Bluetooth Module Address AT Command

    Dear Members, I am using HC-09 Bluetooth module. Is there any AT command throug which I can get Bluetooth ID of that particular module. I am talking about Bluetooth ID which looks like as 01:15:E4:0C:6F:AD Thanks in advance. Best Regards
  11. G

    ETD 49 TRansformer Calculation

    Dear All, I have following issues in SMPS Inverter. I am making a 1KVA system.Is ETD-49 enaugh for 24V to 350V DC-DC Boost Converter working @ 40KHz Push-Pull ? What are the steps to calculate number of turns for high frequency transformer ? How to calculate guage of wire ? Thanks in...
  12. G

    L6386 High side driver not working

    Hi, Help needed in L6386 based Full bridge. I have copied circuit from ST application notes containig L6386 based IGBT Driver. Lower side driver of ICs is working fine but waveform is not appearing at both high side pins. Voltages on each pin are fine. Need advices to solve this issue ...
  13. G

    89s52 with Xbee pro and UART help

    Dear, A level conversion circuitry is needed to connect data lines communicating at different levels. Do not reduce the VCC for microcontroller and also do not try increase VCC for Xbee. CTS and RTS are used for handshaking during communication. You can leave them open . Connect Dout of Xbee...
  14. G

    Connection between 2xPIC16F877A using UART

    Hi Dear , There is no need of MAX232 to communicate two microcontrollers. Just connect as connected in attached image. Regards, Gapoo.
  15. G

    microcontroller parallel programming, how?

    Dear Andro, You should use single timer micro-controller with two timers. Such micro-controller are easily available. Regards, Gapoo
  16. G

    SIM900B not sent to SMS!

    Hi +CSQ 0,0 means that modem is not getting the signals. The antenna and terminal will show short on meter since resistance is too low. Check the connections which are between SIM Holder and Modem. It is a common mistake that sim connections are not correct. What message do you receive when you...
  17. G

    PCB design software for a student

    Hi Cadance Orcad is a very good software to make your schematics, PCBs and Gerber files. You can easily edit existing parts and cerate new parts for your schematic in capture and also in layout. Availble libraries are also very accurate and helpfull. Thanks. Regards. Gapoo
  18. G

    [SOLVED] darlignton array helpppp!!!!!!

    Connect in the shown configuration. When you provide high from PIC's pin respective LED will glow since ULN2803 inverts the signal at the output. Use 1.2K Ohm resistor if you want to give +12V to the leds. Also use +12V at common terminal of ULN2803 in this case. Thanks Regards Gapoo
  19. G

    Nexys 2 Board LCD Help

    I am new to FPGAs I need help to display an string on 16x2 alphanumaric LCD on NEXYS 2 board. I need step by step aproach from begning of the project in Xylinx ISE suit. Thanks in advance. Regards gapoo

Part and Inventory Search

Top