Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Search results

  1. M

    [SOLVED] defination of linear element

    okay okay!! So i was mixing up the definitions of a linear equation and a linear operator! Thank u c_mitra & vGoodtimes! that solved my doubt :)
  2. M

    [SOLVED] defination of linear element

    why is it said that a device having an equation of the form y=mx only for its IV charc is a linear element? why cant it be y=mx+c?
  3. M

    [SOLVED] trouble with serial communication using dspic30f2020 & matlab

    I changed my crsytal...its working now :) thank u so much :):)
  4. M

    [SOLVED] trouble with serial communication using dspic30f2020 & matlab

    i tried debugging by displaying the value i receive on an array of leds...as a result i realised that when i send 1, it receives 129 (i.e 0b10000001 instead of 0b00000001)...and this is happening for all the other numbers..i.e. for some reason, the msb is always set high :/...so if i check the...
  5. M

    [SOLVED] trouble with serial communication using dspic30f2020 & matlab

    hi again everyone! I am trying to interface a matlab gui with dspic30f2020 over serial communication. My matlab code sends a number (here 67) when i press a certain pushbutton. The muc is then supposed to check if the value received is 67 and if it is, then it has to take a certain action...
  6. M

    [SOLVED] problem with serial communication using MATLAB and dspic30f2020

    Hi everyone! I have a slight problem here. I am basically trying to sample 200 analog values using the ADC inside dspic30f2020 and then sending them via UART to a matlab program. The thing is, I am sending these 200 values to matlab only once (as far as my understanding goes, in my code for...
  7. M

    [SOLVED] dsPIC30F2020, problem with calculation of sampling rate of ADC

    thanks susan, I get it now. But i have one more doubt, in the data sheet, in many places its written that the controller works at 30 MIPS when an external oscillator of 15 Mhz is used and PLL is enabled. Now i am assuming that this 30 MIPS comes from the instruction clock frequency i.e. Fcy...
  8. M

    [SOLVED] dsPIC30F2020, problem with calculation of sampling rate of ADC

    can somebody please tell me how microchip calculates the maximum sampling rate of the ADC of dspic30f2020 to be 2 mega samples/sec ? I tried going through the datasheet but was unable to figure it out :/
  9. M

    [PIC] problem with uart TRANSMISSION (using dsPIC30F2020, matlab and ft232)

    Hi everyone, i have written a small code to transmit 5 numbers from matlab to the PIC via FT232. Depending on the number received, a particular led blinks. When the number 5 is received, the MUC transmits back all the 5 numbers received till then to the pc @ 115200 bps. For some reason my...
  10. M

    [SOLVED] problem with UART RECEPTION: using dsPIC30F2020, matlab, FT232 & c30 compiler

    re: problem with UART RECEPTION: using dsPIC30F2020, matlab, FT232 & c30 compiler thanks a lot Susan! the first line itself helped me out..completely forgot to call initUart. My code is working now :)
  11. M

    [SOLVED] problem with UART RECEPTION: using dsPIC30F2020, matlab, FT232 & c30 compiler

    Hi guys, i am trying to write a small program to test serial communication between dsPIC30F2020 and MATLAB via FT232. As per the program, a random number is sent from matlab to the PIC. On reception of the number via UART, an interrupt is generated and an LED connected to pin B0 should glow...

Part and Inventory Search

Top