Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Search results

  1. G

    Why two types of input impedance in laboratory instruments?

    Thanks for the replies! What about the parallel capacitance then? Is it needed or it is a parasitic capacitance?
  2. G

    Why two types of input impedance in laboratory instruments?

    Hi, in some laboratory instruments (i.e. Network analyzers) the provide two kind of input impedances : 50Ohm and 1MOhm // 20pF. I understand the 50 Ohm , is the standard for maximum power transfer but why the 1MOhm parallel with 20pf? Where is this needed and how it is exactly implemented...
  3. G

    Interfacing microcontroller to 1GBPS laser driver

    All VCSEL laser drivers that I could find operate from 1GBPS. The MAX3798 is prefect for my application since it is both receiver and transmitter and it has programmable bias and modulation current. Can someone propose another driver or mixer ic? Otherwise maybe I should try and design my own...
  4. G

    Interfacing microcontroller to 1GBPS laser driver

    I don't need to use the full 1GBPS Bandwidth, just a few MBPS is fine, but the laser driver IC is for 1GPBS applications. Do u think a Serializer/Deserializer (SERDES) will help?
  5. G

    Interfacing microcontroller to 1GBPS laser driver

    Dear all, I want to interface a microcontroller with the MAX3798 laser transceiver ic. The problems are: 1. The MAX3798 has CML (current mode logic) for transmit and receive data but the microcontroller uses 3.3V or 5V voltage logic. 2. The minimum data rate of MAX3798 is 1GBPS but the...
  6. G

    Laser diode and photodiode circuit

    Actually I found a driver ic with similar topology: Any ideas how to implement it with discrete components?
  7. G

    Laser diode and photodiode circuit

    I was thinking something like this for adding the modulation current: Will the switch cause spikes in the pulses? What Voltage controlled current source do you propose?
  8. G

    Laser diode and photodiode circuit

    Hi all, I want to control the Bias and Modulation current of a laser diode using a microcontroller, a DAC and discrete components (including operational amplifiers). Current range 3mA to 25mA with 0.1mA step. Current pulses: rise time few nanoseconds, 10% max overshoot I have found this...
  9. G

    Linear power supply series transitor

    Thank you for the answer. The R7, R8 will remain constant. I will not use a pot to change the voltage but I will control the V2 from 0 to 5V with a DAC and microcontroller. Basically, because of the 1/10 voltage divider whatever i put at V2 gets multiplied by 10. ie. Vout = 10*V2 Q2 is used...
  10. G

    Linear power supply series transitor

    I am trying to figure out this simple configuration. The idea is, controlling the V2 (vref)voltage to control the Vout. I am thinking of using a microcontroller and a DAC to create the V2. How do I select the resistors values, is every resistor needed? Is the opamp + - inputs ok, or I need...
  11. G

    Linear power supply series transitor

    One more question: How can a adjustable linear supply be controlled down to 0 volts? I see many commercial supplies claiming that.
  12. G

    Linear power supply series transitor

    Thank you for your answer. What I need to know is, how do I calculate the base current depending on the Vout. i.e. when Vout=15V and I want Vout = 16V, I have an error of 1V. How does this translates to additional or less current to the base? Ib= K*(Vdes-Vout). How I calculate K? End when...
  13. G

    Linear power supply series transitor

    Hi, In linear power supplies there is a transistor (usually darlington) that is current-controlled depending on the output voltage. The problem is I cant seem to find the Vout - current-to-darlington-base equation. Do I operate it in the linear region? When Vout < Vout_desired do I saturate...
  14. G

    Lab power supply earth output function?

    How did u find that there were "random Earth currents flowing around virtually everywhere in the building"?
  15. G

    Lab power supply earth output function?

    So generally, I should connect ground (black) to earth(green) outputs for safety?
  16. G

    Lab power supply earth output function?

    Hi, What's the use of the earth output in laboratory power supplies? There is already a ground output.
  17. G

    Commercial power supply design

    Hi, I was wondering if there are standard design for commercial programmable power supplies such as these: https://www.keysight.com/en/pc-1000003110%3Aepsg%3Apgr/176-1200w-dc-power-supplies-gpib-single-and-multiple-output?nid=-536902293.0&cc=US&lc=eng Are they based on SMPS or linear...
  18. G

    Boost DCDC converter step response

    Hi, I designed a boost DCDC converter 11V to 19V @3A load in CCM and a voltage mode type 3 copensator. I get this step response from simulation. Is it ok or should I redesigned my compensator? Steady state response is ok, but I am worried about transient response. Should it be without...
  19. G

    LCL and FCL differences

    What is the difference in functionality between LCL (Latching current limiter) and FCL (Foldback current limiter) and in which applications are they used?
  20. G

    Taper Charge Mode for batteries

    hi all, What is Taper Charge Mode and how can I implemented with a commercial programmable power supply?

Part and Inventory Search

Top