Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Search results

  1. M

    how to read a file from verilog

    in the testbench or top module u can use the $readmemb for reading file. do refer verilog LRM it will give u every ans u need syntax: $readmemb("file_name.ext", var_name);
  2. M

    Fresher VLSI Verification Engineer looking for a job

    Hello to all, i am a fresh VLSI engineer looking a job as an verification engineer and require some guidance on making a proper professional looking resume so here i am attaching my resume plz help me guide. thank u
  3. M

    Digital electronics circuit design

    actually i thought of that but the problem is that the op of the divide by 2 circuit will be high for whole cycle till next posedge of clock, but here it goes low whenever a negedge of same cycle, so i need a more optimized circuit rather than just divide by 2
  4. M

    Digital electronics circuit design

    i want the circuit and a proper method to Design a black box whose input clock and output relationship as shown in diagram. __ __ __ __ __ __ __ __ __ __| |__| |__| |__| |__| |__| |__| |__| |__| |__ <<<<<<< clock __ __ __...
  5. M

    Adc help required for samling signal from e700 pir sensor

    hello, i have a prototype board wit e700 pir sensor attached with lm358 and its op is given to pin 1.1 of msp430g2131. plz give me hints to program it to detect motion.
  6. M

    Motion detection using MSP430g2131

    m trying that...i got it configured right...still its not working..i want sampling to start when ip comes to pin1.1..so can i use port interrupts with adc interrupt
  7. M

    Motion detection using MSP430g2131

    no, it didnt helped. plz give suggetions for using adc for sampling
  8. M

    Motion detection using MSP430g2131

    sir, thankx... but, after reciving sample i have to start conversion, so can i put an interrupt for reciving signal, then starting the conversion in ISR - - - Updated - - - and is the configuration for adc done right for continous sampling. m not using launchpad, its a prototype device for...
  9. M

    Motion detection using MSP430g2131

    i have this availiable device its p1.1 is attached with o/p of the PIR sensor. so hav to make it as an input. where to put delay? at start? can i use WDT for delay
  10. M

    Motion detection using MSP430g2131

    i have this code built as i am not much used to programming with ADC's so plz suggest changes in code required. i want to get led glowing for 3 seconds wen it detects motion then should go off. #include <msp430g2131.h> #define LED_OUT BIT6 // Bit location for...
  11. M

    MSP430p149 programming

    hello all... i am newbie for msp430 nd recently got the olimex msp430p149 development board. so nay one can please help me to get the proper compatible jtag cable to program it as i am not able to do it with rs232.
  12. M

    Help me solve invalid storage class error in MSP430 code

    Re: error in code MSP430 even if followed by semicolon it gives of error of invalid storage class.
  13. M

    Help me solve invalid storage class error in MSP430 code

    Re: error in code MSP430 #include "msp430x14x.h" #define PWM_Period 3999 // 8MHz / 4000 = 2kHz #define PWM_Max 1199 // Max duty factor used #define PWM_Min 149 // Min duty factor used #define MIN_SPEED 10000...
  14. M

    Help me solve invalid storage class error in MSP430 code

    Re: error in code MSP430 but how to solve it
  15. M

    Help me solve invalid storage class error in MSP430 code

    WDT_ISR(Wdt_ISR) __interrupt void Wdt_ISR(void); __bic_SR_register_on_exit(LPM0_bits); wats error in these lines...it says invalid storage class
  16. M

    MSP430 microcontroller msp430g2231 4x4 matrix keypad interfacing code in c

    your c source code link is not providing any code downloads..... my code is same that is in the pdf file of ultra low power keypad
  17. M

    MSP430 microcontroller msp430g2231 4x4 matrix keypad interfacing code in c

    its 3x4 i want 4x4 and for msp430g2231 i alredy tested it in ccs4 but it has errors for msp430g2231
  18. M

    Code for interfacing 4x4 keypad to a microcontroller

    Re: read keypad in proton picbasic hello can you please post a similar program for msp430g2231
  19. M

    MSP430 microcontroller msp430g2231 4x4 matrix keypad interfacing code in c

    hello can any one give me the code for 4x4 matrix interfacing in launcpad using c.

Part and Inventory Search

Top