Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Search results

  1. S

    Orcad PCB Editor. Problem creating Artwork

    Hi there, I'm not an PCB layout expert. This is my third time using Orcad PCB Editor 15.5. Previous occasions things were setup for me, such as the layers, sheet size, etc. With that said, I'm having problems generating Artwork for my 1 layer board. The top etch layer is not coming out...
  2. S

    Links to two EMI Solutions producers

    Easy EMI solutions h**p://www.tkk-nets.jp/products/debjiha/denjiha/index.html h**p://www.nec-tokin.com/english/product/busteraid/features.html :D
  3. S

    Puzzle: Distinguising equivalent circuits inside black boxes

    Can someone tell if it is possible to distinguising the following two black boxes: Box 1 - From the interfacing box's terminnal a 1V ideal voltage source with a 1Ohm Resistor in series is connected. Box 2 - From the interfacing box's terminal a 1V ideal current souce with a parallel...
  4. S

    Problem with QAM data spreading due to LPF

    QAM Spreading due to LPF Hi I am modulating OFDM symbols, sending it out to filters, performing low pass filtering with proper BW specs. , then sampling and demodulating the signal by taking the FFT the plotting the QAM symbols on the constellation. --no channels are involved. If you...
  5. S

    What is the SNR in this ADC ?

    Finding SNR Hello, This equation is for an ADC: SNR = 6.02n + 1.76 dB , where n is the number of bits However, this equation has a few assumptions and is invalid if your input clips and saturates the ADC. Assuming my input signal does clip and has a guassian distribution, what is the...
  6. S

    TI - 6711 pinout (where to find CLKS ?)

    TI - 6711 pinout Hello, On the DSK6711 from 'TI' i am confused about where to find CLKS on the external J2 connector. Where is this pin? Does it share a pinout with one of the serial ports? Sparrow
  7. S

    3.3V driving 5V digital. how??

    What device do I need to help interface 3.3V digital output to 5V input on CPLD??? I just have 3 signals to interface, with max freq of operation at 75MHz. I would like to be able to buy the component from Digi Key. Sparrow
  8. S

    Which motorola phone can be converted to a gsm scanner?

    Gsm S@nner hi! Which phone from motorol@ can be easily converted to a gsm sc@nner?? Anyone with relavent links to more info on this??? thnx Sparrow
  9. S

    DSK6711: McBSP1 Tx to McBSP0

    pcm3010 project Hi all, I am a newbie at the DSK6711. I can't seem to get the McBSP1 transmit to McBSP0 on the same C6711DSK board through hardwiring the J2 connector in the following fashion. DX1 -> DR0 CLKX1 -> CLKR0 FSR1 -> FSR0 Where: McBSP1 will send the synch pulse &...
  10. S

    The working theory behind the voltage control circuit in this copitts common base VCO

    Hi :) Can any one tell me the working theory behind the voltage control circuit in this copitts common base vco[attached jpg]. The voltage control ckt is in the centre of the figure. So plz explain the following: *purpose of resistor[1000ohm] from between transistors. Center and left...

Part and Inventory Search

Top