Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
I was wondering if anyone knows what the DC pin is for and stands for? I've tried to asked Vishay tech support unfortunately there was no reply....
Data sheet can be found here
Thank you for your help!
coupled inductor equation
I was wondering if someone could help me figure the state space equation for this circuit, according to the coupled inductor equation
V1 = L1 di1/dt - M di2/dt
V2 = -M di1/dt + L2 di2/dt
which gives me
V1 = 1 di1/dt - 1/2 di2/dt
I am looking to get an ICD2 and was wondering if anyone could help me with these questions.
Coming from a motorola hc11 background, I use Jbug11 talker to test my ciurcuit connected to the hc11 eg. by placing values to port A and B etc... then examine if the circuit is...
Quote~"If two one-second collections of 1 Coulomb each were concentrated at points one meter apart, the force between them could be calculated from Coulomb's Law. For this particular case, that calculation becomes
The density of metallic copper is about 9 grams/cm3 and one mole of copper is...
I was wondering if anyone could give me any suggestions on what I should do, at the moment I have a batch of PIC16C73A and these are one time programmable(OTP) micros and because they are OTP micros, I would not be able to develop programs using this chip without wasting them and I...
I was wondering if anyone can explain what is a multiplying DAC and what is it used for?
Can a normal DAC be used as a multiplying DAC by simply adding a Rf to Iout ?
Thanks in advance! :D
I was wondering if any knew where I can buy CRT sockets??
I am looking for the CRT socket for Wells Garder K6100 monitor, CRT model 19VLUP22.
Would be greatly appreciated if anyone can give me a lead, thanks in advance!
Current doing math and having problem understand the relationship between trig and euler's rule, how does one represent/convert to the other term?
**broken link removed**
**broken link removed**
Any good ebooks here at eda download you would recommand?? I have tried the university...
I am looking to construct an audio spectrum analyzer (bandwidth ≤ 20khz) using super heterodyne but I am not quite sure what part I should use, I am aware of mixer ICs on the market but their purpose are mainly focused for communication use. After reading the book...
I am poundering on the idea to use reactive components such as inductors and capacitors to build a temporary power storage medium such as a battery but I an not quite sure if this is possible, can anyone give me any advise and guidance to see if this is possible??
My aim is to...
A while back I saw banner on the forum for PCB prototyping in china but I can no longer find the link, can anyone direct me to the link for this? or Are there any other cheap fast turn around PCB prototype service available that you would recommand??
Thank in advance!
monitor x y
I have a HP 3581 wave analyzer and I am looking for BIG x-y monitor for it, I was wondering if it is possible to use computer CRT monitor for this purpose? eg. connect x-y to certain pin of the CRT connector?
Does any one know if waveform monitor can be used for this as...
Prot*l 99SE question
Does anyone know why when place an op amp eg. TL074 chip in the schematic it does not show supply voltage pins of the chip? I am trying to make a PCB layout but just wondering why the chip does not have Vcc pin so I can place power ports to the pin.
I am looking for a free ware that allows me to construct the schematic and import the netlist to PCB layout for track routing, I don't need more than 2 layers. However, I would like to be able to assign/change the pin number to customise an opamp in case they do not have the particular op...
I was wondering if anyone can recommand a EVM for performing DFT? So far I have looked at the TI and AD's EVM packages and am trying to decide between the AD BF533 EZ-KIT Lite and the BF561 EZ-KIT Lite, since they both have audio/video input and output which makes them very handy...
I am looking to decide to get a DSP EVM kit and am looking for some advise on which one to dive in, my main application will be audio and LCD/video eg. sample audio and apply FFT to display on LCD much like a spectrum analyzer.
Currently I am looking at TI's TMS320C6713 DSP...