Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Search results

  1. A

    if place the component in the board get as overlap ,whether it can error or not?

    hi buddy's i am using orcad software for pcb board designing, i have net listed the circuit , and while place the components getting overlap , because the board dimension is poor. so my doubt is whether if i place the component like this whether i get the error or not while...
  2. A

    how am i become as you like good pcb board designer?

    hi Super Seniors , i am Ramakrishnan , from india, i just done Bachelor of engineering in the field of ELECTRONICS AND COMMUNICATION ENGINEERING , Basically i have interest in the electronics field. for that i just finished orCad course without appropriate teaching, so now , by my interest in...
  3. A

    here some error in the circuit (ohm meter circuit)

    hi buddy's here i have attached my circuit, i have small in this ... that means i have drawn the circuit in the orcad 16.0 and practically checked this circuit i didn't get the noted output in both ways ,,,, in this two condition should i connect the input 5V with the...
  4. A

    how to and what are the rules and ways create the foot prints?

    hi seniors, i have doubt create the foot prints in orcad , i created one project and in which one 15 pin connector there. for that i just wanna create foot print ,but everytime i am getting error like pin 1 is missing pin 2 is missing likewise all pins . i had used that orcad pcb designer...
  5. A

    foot print created rules for symbols

    hi buddy's i am using orcad16.0 and i created one project , created footprints for corresponding symbols, even also i shows some error while netlisting IT shows some refdes error , but i gave the name of the symbol while creating the foot prints, but no use couldn't clear...
  6. A

    ERROR while netlisting

    hi dudezz,, i am using orcad 16.0 , and i have tried so many times ,but unusually i did not get error less circuit and board .,., so please guys take your time for my project , please consider it i have attached my three project and created foot prints also , you know its having...
  7. A

    not updating pcb board while netlisting

    hi,,, i have created three project ,i 'm using ORCAD 16.0 . already i posted one of the error from the one of my project. now , while i netlisting the three project , all the three project has this kind of same error,, please solve it, i have attached that three projects session logs...
  8. A

    device/symbol check error detected

    hi buddy's.,,,,,,,,,,, i created one circuit , in which i've use three TRIMPOT , and also created foot print respectively. i gave a foot print name corresponding column for corresponding symbol , but , in three TRIMPOT's , one TRIMPOT only have this error , but i gave...
  9. A

    Create symbol started.

    Hi gusy !! ! i 've one doubt when a create a foot print symbol for IC , i got this warnings and errors , how am i solve it ? and if i place symbol for foot print , will i get any error during the netlisting & and also give some tips to create error less symbol please...
  10. A

    i need some orcad pcb editing & designing notes or material

    hi guys ! ! ! i am new for orcad , just i simply finished the course in centre. but i didn't get the depth knowledge in pcb designing there .... so if you have any handwritten or some other material for orcad ,,, please send me thank you...
  11. A

    netrev failed & Device/Symbol check error detected

    hi SENIORS ! ,i am a one of B.E ECE 2012 passed out student , so i am new for orcad . i have so many doubts ,few things is below. i have designed one circuit in capture, in which i was created three components with circuit and also designed the foot print in pcb editor, when i creating the...

Part and Inventory Search

Top