Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Search results

  1. I

    How to Start a videocall with AT commands

    at command for video call Hi ! I have an UMTS modem and I want to made a video call. How I can do this ? I have searched into AT commands but I haven't found anything Thanks !
  2. I

    Putting into sleep mode and waking up RS 485 transceiver

    RS 485 wake up problem Hi ! I have the following question: I have to do a network of devices based on PICmicro. This network in a RS485 and the device is battery powered. For save the battery I put in sleep mode the PIC micro and I want that when there's a RS485 comunication all pic wake...
  3. I

    Problem with LTC 6915 and negative voltage value

    LTC 6915 problem Hi ! I have a problem with the linear tecnologies's IC LTC6915. We used it for amplifier the output signal of a Wheatstone bridge , and this output can be negative. For this reason we used a voltage regulator of 1,25 V connected with the Ref. Pin. But if I put...
  4. I

    1-wire Search ROM routine

    one wire search rom Hi ! in my case I had to interface some 1-wire devices with a Microchip PIC, for did it I used a PIC's PIN , without any Transport DS2484. If you want I can post you my code, it works well . The only thing that you have to do is to adapt it to your requirements .. Regards
  5. I

    mini motorcycle rpm counter

    motorcycle rpm counter Hi ! I have to do a rpm counter for a mini motorcycle. I have to take a signal from the coil of motor and put it inside a microcontroller, but I don't know the features of this signal and then I can't design a signal contitional block. The only thing that I know is...
  6. I

    RTD conversion formula

    pt100 formula Hi ! Does someone knows where I can found the conversion formula of RTD from resistance to temperature and vice versa ? Thanks
  7. I

    ds2760 for thermocouples measurement

    Hi ! I tried to use the ds2760 IC for thermocouples measurement. I found this project in the follow Maxim application notes: https://www.maxim-ic.com/appnotes.cfm/appnote_number/991 The ICs have some points of no linearity, and this points is different from IC to IC. I...
  8. I

    1-wire Search ROM routine

    search rom Hi ! I have to interface a PIC to a 1-wire bus with 3 devices. I have just used some 1-wire devices , but I haven't used a 1-wire bus. Has anybody done a 1-wire Search ROM routine ? If it's possible , can you post me your source code ? Tnx
  9. I

    An internet site about Battery

    Hello ! Does anybody know an Internet site who talk about batteries types with their characteristics and their employment ? Thanks
  10. I

    How to make a circuit with one exit using AD420 IC ?

    Re: Static rele It's true, but with this solution I can't set the exit type via software. In fact if I understand what you say, I must put the resistance on the current exit, if I want a voltage exit, instead if I want a current exit the resistance is not necessary.
  11. I

    How to make a circuit with one exit using AD420 IC ?

    Static rele Hi ! I have the following problem: I have an IC ( AD420 ) with 2 different exit , a current exit , usually 4-20 mA and a voltage exit, usually 0-5 V . I want to do a circuit with only one exit , where I can select the exit type via software, but for do this I must...
  12. I

    How to access the AD8555 register using PIC microcontroller?

    Re: ad 8555 My memory fails... You have reason, after the end packet I can read the output of AD8555. But my problem remain. I don't read a correct value.. Now I'll try to check the Vdd Value . Thanks for now. Added after 4 hours 9 minutes: I think, It was a bad voltage regulator...
  13. I

    How to access the AD8555 register using PIC microcontroller?

    Re: ad 8555 It's true , "It dosnt look that difficult" .... I use a scope for debug and I'm sure that I send the 38 bit correctly. But when I use the reading function, I see that the IC doesn't respond correctly. The response must start , if I have a good memory, after the 2 dummy bit ...
  14. I

    How to access the AD8555 register using PIC microcontroller?

    Re: ad 8555 You are step ahead... Thanks for yours illuminate councils !!!
  15. I

    How to access the AD8555 register using PIC microcontroller?

    ad 8555 Hi ! Someone has used the IC AD8555 from analog device, with a PIC microcontroller ? I need an example that explain how access in the IC register. Thanx.
  16. I

    Thermocouples measuring with an A/D converter

    Thermocouples misure Hi ! Someone have done an amplifier stadium for read thermocouples with an A/D converter (with full scale of 4.7 V) ? I would want to use this circuit for reading more types of thermocouples. Someone can help me ? Thanx
  17. I

    Project for sending data across power line

    Re: Data across power line This is a good point. I don't need a hight speed communication. But if I use a 24 V dc power source There is somenthing else ? Thanks
  18. I

    Project for sending data across power line

    Data across power line Hi ! I have the following problem: I want to do a network like RS485 , a master and some slaves, using the power line for the power supply and bringing the data signal. I have seen that microchip do this with his onewire, but I need that the length of network...
  19. I

    How to change a lens and field of view in pyrometric sensor?

    Re: Lens and Field of View Ok I have a plano convex lens and I tried to put in front of my sensor. I putted my sensor on the focus of lens but it doesn't work, the field of view remains quite the same. How will you put the lens ?
  20. I

    How to change a lens and field of view in pyrometric sensor?

    Lens and Field of View Hi ! I have a Pyrometric sensor and I want to change his field of view. I want to do a non-contact termomiter and I need to have a tightened filed of view. In the datasheet of sensor there is only the graphics of field of view. Moreover my sensor has an internal...

Part and Inventory Search

Top