Search:

Type: Posts; User: andre_teprom

Page 1 of 20 1 2 3 4

Search: Search took 0.08 seconds.

  1. [SOLVED]Closed: Re: ACS712-5A AC Current Reading - How to?

    ...moreover, with the above code it is being hold the maximum peak-to-peak, not updating with further smaller values.



    You should compute the average value (sum divided by amount of samples);...
  2. [SOLVED]Closed: Re: ACS712-5A AC Current Reading - How to?

    As clearly stated there, it is a transformerless circuit designed to do the same job of a current transformer, so it has the same issue regarding the rectifying output diode.
  3. Replies
    4
    Views
    317

    Closed: Re: problem with arduino

    You are cascading the output of one chip into another input, which in an offboard arrangement like using Arduino can mean a degradation in signal quality; By the way, you have not shown any detail of...
  4. Replies
    2
    Views
    249

    [PIC]Closed: Re: XC8 XLCD with PIC18 error

    It is worthy to try adding an while(BusyXLCD()) command after each XLCD access just to check if you are having timing issues.
  5. [PIC]Closed: Re: PIC16F1934 Timer0 and some other stuff

    Unless I overlooked something, you did not mention what compiler you are using. Most often an interrupt vector is defined preceeded with a '#' directive. The way you did, it was nothing else than...
  6. [PIC]Closed: Re: PIC16F1934 Timer0 and some other stuff

    Once you are apparently using interruption with just one timer, checking the interrupt flag right after entering into interruption vector seems unnecessary, there it is supposed to be set as 'true' ....
  7. Replies
    5
    Views
    427

    [SOLVED]Closed: Re: Ground plane in audio amplifier?

    it is likely being not self oscillation as you think, but rather a bare injection of EMI ( e.g , from mains ) through your fingers.
  8. Closed: Re: Energy doesn't FLOW the way you THINK! (Electrodynamics)

    Each model of representation of a physical phenomen is appropriate to the school level in question. For example, quoting the Poynting vector makes sense only when the student is familiar with the...
  9. Replies
    1
    Views
    268

    Closed: Re: Altium Width Rule Issue

    You can consider making rules that are applicable for specific devices only, with the Query Builder feature available either on Schematic or PCB scopes. The `PartDesignator` parameter is one...
  10. Replies
    2
    Views
    164

    Closed: Re: Pic32 qei interrupts

    In general interupts are not used with QEI registers, but rather with Timers; we want to take the current position at fixed intervals and then calculate the speed or just check whether certain...
  11. Replies
    9
    Views
    436

    Closed: Re: reason for 50 Hz ac current

    Instead,



    There is currently a plethora of equipment which extracts samples from the network mains in order to synchronize their PLLs (e.g UPS, TV, etc...), and therefore however much the...
  12. Closed: EPLAN: How to represent bundled connections of a cable?

    Does anyone have any tips on how to make a visual representation of a cable in a multiline diagram, bunching all the connections within a single line ( such as in Altium with the Bus Entry feature ),...
  13. Closed: Re: RC Filter for Web Based PWM Controller (NodeMCU + ULN2803)

    Although at first sight the motor 210mA lies within the specification of the ULN2803 datasheet - which is 500mA for each transistor - you will notice that there is a graph for the duty cycle which...
  14. Closed: Re: RC Filter for Web Based PWM Controller (NodeMCU + ULN2803)

    With regard to RC filtering, it would actually have some usefulness to reduce the generation of harmonics due to PWM switching on a typical reactive load like a Fan, but that would make sense only if...
  15. Replies
    4
    Views
    539

    Closed: Re: Learning psoc technology

    At a glance seems a good choice to start since this development kit is made with the CY8C5888LTI-LP097 microcontroller, which has built in either an A/D and D/A converter along with a considerable...
  16. Replies
    3
    Views
    1,239

    Closed: Re: Simple free mechanical drawing package?

    From what you said, there is not only one 3D format that you have to work with, and considering that the purpose is only to generate the 2D projections, it could be the case to consider exporting...
  17. Closed: Re: What is the size of terminal connector

    The above snapshot refers to the positioning properties of the component (apparently on schematic viewer), does not get into the component details. To do so, you must edit it in the library editor. ...
  18. Closed: Re: What is the size of terminal connector

    As depicted on datasheet, pin dimensions are 0.5x0.9mm, whereas the recommended hole diameter (in fact not so clear) is 1.1mm.
  19. Replies
    12
    Views
    656

    [SOLVED]Closed: Re: RF Detector circuit design

    It is not your first thread on the scope of RF detector and people have been giving you several advices that you should consider instead of refusing them, particularly when you admit to be "not...
  20. Replies
    3
    Views
    1,080

    [SOLVED]Closed: Re: Why is CO2 a green house gas?

    Another point to consider is that due to the complexity of the structure of the chemical compounds present in the atmosphere, from the simplest (atoms) to the most complex (molecules), there are...
  21. Replies
    3
    Views
    1,080

    [SOLVED]Closed: Re: Why is CO2 a green house gas?

    It is just a matter of absorption efficiency of gases along with their concentration in Atmosphere, in fact all gases absorb energy from EM waves, however CO2 in particular, has a maximum absorption...
  22. [SOLVED]Closed: Re: Generation of 4 Phase Shifted clock Signals

    With basic components you will be able to create delays, not properly a phase in the usual sense of this expression in digital electronics. A frequency dependent timming approach should be always...
  23. Closed: Re: Holding button for 2s to trigger 555 timer

    Instead of the standard resistor/button arrangement on the 555 input used on the monostable configuration (resistor on the top, button NO on bottom), try replacing it by a voltage divider with 2...
  24. Replies
    2
    Views
    274

    Closed: Re: At45db041b vs at45d041

    Many programmer's tools check the chip device ID and refuse to download the code if the target differs from the part selected, unless you uncheck this option - when available. Even a bare suffix...
  25. Replies
    9
    Views
    931

    [SOLVED]Closed: Re: USB to RS232 exactly similar to COM1

    What has not been clear here so far is the purpose of this port in your application, whether only communication or communication + power supply. Some older native COM port-based programmers...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4