Search:

Type: Posts; User: FvM

Page 1 of 20 1 2 3 4

Search: Search took 0.36 seconds.

  1. Closed: Re: Magnet core inductor out of TV set, what is is used for?

    The photo in post #7 seems to show a simple coil with ferrite core. Are you sure that it involves a permanent magnet? Due to the open magnetic path, the core has only limited effect on the coil...
  2. Replies
    4
    Views
    250

    Closed: Re: Stuck at simulations of Amplifier in LTSpice

    Capacitors are zeroed during initial transient solution, thus a SPICE simulator has no problems with large capacitors, as long as the large signal operation point doesn't differ from the initial...
  3. Replies
    2
    Views
    74

    Closed: Re: Frequency Module IGBT

    I can't imagine many configurations where the switching frequency per module is higher than per transistor, anyway the datasheet specification is surely per transistor. But the number gives only a...
  4. Replies
    1
    Views
    105

    Closed: Re: Photodiode SFH205FA in PSpice

    Find photo diode models at https://www.osram.com/os/tools-and-services/downloads/index.jsp

    Basically a Si-diode + a current source to model the irradiation.

    The basic diode without the current...
  5. Closed: Re: Magnet core inductor out of TV set, what is is used for?

    "S" correction choke is a good guess, but there are many different magnetics, particularly in a color TV. It's about 20 years since I did the last CRT TV repair.
  6. Closed: Re: Huge difference between results from schematic simulation and momentum co-simulat

    I believe that you see large differences with the said "extreme" microstrip geometry. Unfortunately I can't locate a comparison of both results in your threads.

    Like Volker, I would trust the EM...
  7. Closed: Re: Magnet core inductor out of TV set, what is is used for?

    Why not show a photo?
  8. Replies
    8
    Views
    306

    [SOLVED]Closed: Re: Help for Assembler 12F675

    Sounds self-explanatory to me. It's Proteus.
  9. Replies
    9
    Views
    355

    Closed: Re: PWM Ramp Voltage of SG3525

    To calculate the modulator gain, you better refer to the typical rather than marginal threshold values, 0.9 - 3.3V.
  10. Replies
    7
    Views
    358

    [PIC]Closed: Re: Question About Crc8 Picbasic Implementation

    The answer was already given: Yes.

    That's how CRC calculation works, you initialize the CRC variable, call the routine for every message byte and have the message CRC.
  11. Replies
    7
    Views
    358

    [PIC]Closed: Re: Question About Crc8 Picbasic Implementation

    You need to review the PICBASIC manual. HEX2 means two hex digit formatting.

    In my view, the original question hasn't much to do with CRC algorithm. It's more general how to implement a specific...
  12. Replies
    9
    Views
    400

    Closed: Re: Current Density PCB track

    No. Small trace is dissipating most heat by lateral conduction, thus higher specific rating. Large plane must dissipate all heat vertically. By the way, radiation plays a minor role in heat...
  13. Closed: Re: DCDC module recovery from input overvoltage involves a time delay?

    Always a good idea to read the manual completely. Review page 13.
  14. Replies
    10
    Views
    1,336

    [SOLVED]Closed: Re: Device Support for MAX10 FPGA

    A function in device setup

    159629
  15. Closed: Re: Figure out the dimensions for this circuit button for mouse

    I recognize a square tactile switch with two through-hole pins. Important parameters are button height above PCB and pin distance. A popular form factor is 6.5 mm pin distance and 4.3 or 5 mm height....
  16. Replies
    10
    Views
    1,336

    [SOLVED]Closed: Re: Device Support for MAX10 FPGA

    Your question is answered in the MAX10 device overview document, vertical migration paragraph. M02SC324 to M16SC324 are pin compatible. The best way to care for compatibility, also if devices have...
  17. Replies
    10
    Views
    1,336

    [SOLVED]Closed: Re: Device Support for MAX10 FPGA

    I didn't yet pay attention to the fact, that you are referring to an old Quartus version. 17.0 of May 2017 was the first version supporting MAX10. I'm still using Quartus 17.1 of November 2017 for...
  18. Replies
    7
    Views
    358

    [PIC]Closed: Re: Question About Crc8 Picbasic Implementation

    The CRC algorithm as functional as such, question is how it's used in the application, if CRC is initialized correctly, how you feed CRC_IN. This can't be seen from your code snippet.
  19. Replies
    9
    Views
    400

    Closed: Re: Current Density PCB track

    Hyperlynx has a default current density warning level of 10 mA/mil² (about 1700 A/cm²). An 1 oz, 1mm (40 mils) wide trace carrying 2 A, a still acceptable value according to Saturn etc., has already ...
  20. Replies
    9
    Views
    384

    Closed: Re: Upgrading 12v peltier based refrigerator

    Suggest to read this old Melcor application note that gives a good overview of peltier operation. Melcor is now Lairdthermal.com, the classical CP peltier device series is still continued.
    ...
  21. Replies
    9
    Views
    400

    Closed: Re: Current Density PCB track

    If you convert the linked current capacity numbers for typical trace widths to current density, you get a first answer.

    - - - Updated - - -

    Acceptable current density values are set by thermal...
  22. Replies
    3
    Views
    294

    Closed: Re: De Q'ing resistor purpose

    As the question is posted in PCB Layout rather than RF or Analog Design section, I fear it's really unclear what "De Q'ing" resistor means for you. Please give a typical example.
  23. Replies
    2
    Views
    125

    Closed: Re: EMC Threshold range for different circuit

    EMC compliance must be achieved for the final product with typical application wiring (power supply, signal and communication cables). I don't understand what you mean by "have to define dB levels...
  24. Replies
    7
    Views
    303

    Closed: Re: 50 ohm Dummy Load With 50dB Attenuator

    R1 to R4 placement is near to a star topology, but with inappropriate stub impedances.

    Problem is that you can't micro strip lines above 125 to 135 ohms with the used FR4 substrate. This...
  25. Replies
    13
    Views
    640

    Closed: Re: How to detect this impulse?

    Either your assumptions about 5 ns pulse risetime are wrong or they are using unnecessary large bandwidth.

    What's the objective of your measurement system? Detect pulses reliably and e.g. classify...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4