Search:

Type: Posts; User: BigBoss

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Closed: Re: How can i design defected ground structure in AWR ?

    Arrange the layers and associated materials and other stuffs in "Enclosure" box and make the "Bottom Boundry" being as Open.
    Then connect the Ports in according to this new arrangements..Ports...
  2. Closed: Re: Is there possibility to force a filter topology in DA_LClowpassMatch in ADS?

    Append to volker..

    Choose the Filter's Input Output Real Impedances carefully regarding to those impedances to be matched. Choose appropriate values so that matching circuit won't consist of weird...
  3. Replies
    3
    Views
    271

    Closed: Re: 1dB compression point and jamming signals

    Jamming sensitivity is not depended on P1dB Compression Point only ..Non-linearity ( in general speaking ) is figure of merit of an LNA but "the Modulation" is more important than this.
    Coding is...
  4. Closed: Re: Is there possibility to force a filter topology in DA_LClowpassMatch in ADS?

    There is no such definition as Matching Frequency in Filters.. Because Filters are not matching circuits.
    OK, If Input and Output Impedances are properly selected, the Filter may act as a kind of...
  5. Closed: Re: (ADS) There are no components in ADS after importing my PCB layout from Altium

    ODBC++ is not a proper way-especially from Altium- to import into ADS.Use simply Gerber format.. no pain..
  6. Replies
    6
    Views
    254

    Closed: Re: Integrated planar transformer

    I believe that the frequency is too low to couple two layers that are layed down on two different layers.So efficiency of a such transformer will be so weak..
  7. Closed: Re: Questions about the definition of Z-matrix and Zin and Zout

    You confuse z-parameters and Input/Output Impedances of a 2-port.
    z-parameters are "open circuit parameters" and z11 is not equal to Zin ( or z22 is not equal to Zout )
    Pay attention to...
  8. Replies
    4
    Views
    212

    Closed: Re: RF connected/destroyed Load detector?

    So you should check the Load is connected well then you will turn on the PA, is that right ?? If it's so, I would use a switch to check the Load is well connected then this switch will rely the Load...
  9. Replies
    4
    Views
    212

    Closed: Re: RF connected/destroyed Load detector?

    But if the load is disconnected the PA will also be burned due to reflected waves from Open Circuit.. Take this account into..( I presume the PA has a capability to rive 50Vpp signal level..If the...
  10. Closed: Re: Parameters S12 Reverse transmission coefficient

    Imagine an amplifier..It has one input and one output port right ?? If you apply a signal to input port, you achieve amplified signal at the output.
    But if you apply a signal to output port, you...
  11. Closed: Re: Is there possibility to force a filter topology in DA_LClowpassMatch in ADS?

    Filters have only cut-off frequency definition,that's it..The Input/Output Impedances are constant( already defined ) along filter specification frequency..
  12. Replies
    3
    Views
    182

    Closed: Re: RF Power amplifier stability

    Parallel resistors are used at input/output or both..Consider also highpass/lowpass filter combination.
    There are numerous solution for the stability..
  13. Replies
    3
    Views
    182

    Closed: Re: RF Power amplifier stability

    The amplifier may oscillate-not definitely but-.If K<1, the amplifier is conditionally stable so certain load and source impedances may drift it into oscillation.If K<0, the amplifier will probably...
  14. Replies
    3
    Views
    347

    Closed: Re: Spacing Between PCB Pad and HEATSINK

    In order to prevent from electrical arcs , I'd recommend yo to use a adhesive insulator between heat-sink and capacitor pads.
  15. Closed: Re: Parameters S12 Reverse transmission coefficient

    "Quadripole" means 2-Ports right ?? So, since the antenna has one port only, there won't be S12 or S21 etc.It will have S11 only and the quality of the antenna is defined S11 only by s-parameters....
  16. Closed: Re: Is there possibility to force a filter topology in DA_LClowpassMatch in ADS?

    ADS Filter Design Guide does not accept complex load or source impedances. Therefore you should use a closer real impedance-for instance 10 Ohm-then place a simple matching circuit after.
    If you set...
  17. Closed: Re: Parameters S12 Reverse transmission coefficient

    S12 has no dependency on antenna or other RF devices.S-parameters are definitions that relate interrelation of the Ports of a system either antenna or amplifier..
    Can you post a sketch what you mean...
  18. Closed: Re: How to realize inductor from transmission line (micro-strip and CPW lines)

    CPW cannot be used for Inductor Realizations.Especially if the frequency is not sufficiently high, making an inductor by using Transmission Lines is not practical at all..
  19. Closed: Re: How do you choose input power while doing loadpull?

    Yes, you should apply P1dB(in) to do load-pull..Because this point where the nonlinearity starts to become dominant on the amplifier's performance so it's a kind of threshold..
  20. Closed: Re: Input and output matching for LNA design in ADS

    You should check the Optimum Reflection Coefficient for Lowest Noise target then you can add Ls and Lg to bring up this impedance matched to 50 Ohm.
    So the problem is reduced to design a simple...
  21. Closed: Re: Input and output matching for LNA design in ADS

    If you don't know exactly what values they have, use optimization technique to achieve your requirements.
    I don't know what frequency you're working on but they have to be few nH level for 1 GHz and...
  22. Replies
    2
    Views
    244

    Closed: Re: Problem in Cadence Simulation

    For DC blocks, use a high valued capacitor- for instance- 1mF, for DC feeds use high valued inductor-for instance- 1mH
  23. Replies
    3
    Views
    329

    Closed: Re: ADS (advanced design system) install

    If you're student, request license from Keysight..
    ADS is downloadable from Keysight's website but you have to get a valid license.Keysight offers that for a limited period for students..
  24. Closed: Re: How to get S2P files for Avago Technologies ATF54143 Transistor

    There is ADS model file here..
    https://docs.broadcom.com/docs/MPUB-1511
  25. Replies
    6
    Views
    500

    Closed: Re: Noise effects in a power source in ADS

    Dear bilal.habib,

    Since your circuit has no information about noise which is created in it, you cannot achieve any meaningful result.In order to get a consistent result from a Noise Analysis, the...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4