Search:

Type: Posts; User: anilkrpandey

Page 1 of 4 1 2 3 4

Search: Search took 0.01 seconds.

  1. Closed: Re: "Waveguide ports must be aligned with Cartesian coordinate planes" error

    Which simulation software your are using for this design? You can try simulation with lumped port also.
  2. Closed: Re: Regarding 5G antenna types & design guideline if any!

    In 5G instead of radiating energy in all the direction, a group of antennas that’s called Antenna Array, will focus data signal only to communicating device, so signal strength will be very high. ...
  3. Replies
    1
    Views
    1,198

    Closed: Re: Directivity of antenna less than 1

    There must be some issue in design setup ( like absorbing boundary conditions) otherwise directivity is always greater than or equal to 1 (0 dB), antenna gain can be less than 1 (0 dB).
  4. Replies
    4
    Views
    508

    Closed: Re: High gain wideband antenna

    You have to design a broadband antenna to cover entire 0.1 to 6 GHz. Typical broadband antennas include the log-periodic antenna, traveling-wave antenna, helical antenna, biconical antenna,...
  5. Replies
    1
    Views
    631

    Closed: Re: How To bend a patch antenna in HFSS

    Use 'wrap' feature to bend patch antenna on a curved surface.
  6. Replies
    7
    Views
    2,935

    Closed: Re: Tracking in satellite communications

    Special Antenna feed system is design for satellite autotracking. The antenna of the satellite must be pointed accurately toward the earth station antenna with which the satellite is in communication...
  7. Replies
    3
    Views
    593

    Closed: Re: UHF RFID band and its antenna

    Antenna can be made multi-band resonator using various techniques like Frequency reconfigurable Antennas.
  8. Replies
    3
    Views
    1,385

    Closed: Re: N-well antenna effect

    N-well antenna is used to remove antenna error in SoC design. Antenna rules are used in SoC design to check for excessive accumulation of charge on metal during fabrication. Antenna error happens...
  9. Replies
    4
    Views
    1,576

    Closed: Re: MMWAVE Layout and EM Simulation

    You can use advanced "ADS - Virtuoso Interoperability Feature" (Supported ADS 2016 onwards)
    https://www.keysight.com/upload/cmc_upload/All/RFIC_Interoperability_ADS2016.pdf
  10. Replies
    3
    Views
    1,510

    Closed: Re: Patch antenna array.

    It all depends on your antenna feed network design.
  11. Closed: Re: Problem in placing the waveguide for a CAD model SMA connector in CST

    Select the face of the outer conductor ( or inner conductor) of it and I placed the WG port using this pick. The signal in a coaxial line is defined by the E field in between the two conductors, that...
  12. Closed: Re: Help: EM Simulator package required for designing magnetic coupling

    Also, you can use Keysight's EMPro FEM or FDTD simulator
    http://www.keysight.com/en/pc-1297143/empro-3d-em-simulation-software?cc=US&lc=eng
  13. Closed: Re: Error generating netlist when importing momentum component into schematic

    Also, double check which view of EM component are you using in schematic simulation, ideally it should be emModel
    138831
  14. Replies
    1
    Views
    730

    Closed: Re: drawing coaxial feed for antenna

    Antenna simulation with defined port gives almost same result as port defined at the coaxial input. But defenelty port defined at coaxial input will be more close to real world design.
  15. Closed: Re: Exchange format for Keysight Momentum on ADS

    DXF or if you have ODB++ file that can be also used.
  16. Replies
    2
    Views
    2,148

    Closed: Re: ADS to CST layout import

    You can also try ADS DXF file format.
  17. Closed: Re: ADS schematic s-param simulation differce EM S-param simulation

    If possible attach your ADS project also.
  18. Closed: Re: LineCalc parameters interpretation ADS

    What is this 3D shape, it this transmission line ( liek Microstrip line)?
    In ADS, for microstrip line it is like
    136686
  19. Replies
    14
    Views
    2,887

    [SOLVED]Closed: Re: Strange EM cosimulation, Keysight ADS

    Also check defined port impedance for EM simulation, is it same for all port?
  20. [SOLVED]Closed: Re: effective permittivity and wavelength when using air gap

    Are you using Air as substrate ? Interested of air you can also use low dielectric constant Foam materials.
  21. Closed: Re: Broadside Coupled Balun ADS Port Definition

    You can also try SMD or delta Gap port type then make it diffrential in Schematic simulation if needed.
  22. [SOLVED]Closed: Re: Warning message when converting layout to schematic

    In layout for EM simulation, ground symbol is not required so you can delete these ground symbol in schematic before layout file generation.
  23. Replies
    1
    Views
    740

    Closed: Re: Please help! ADS Layout

    You can hide component text easily by un-checking visibility of layers Silk_Screen-1 and Silk_Screen-2
  24. Closed: Re: How we can make EM co-simulation of circuit

    You can design models for these components whether these are 'Circuit' model or 'EM' model. For more details search ADS documentation how to include these.
    Another way is to flatten your layout...
  25. Replies
    6
    Views
    1,919

    Closed: Re: Transformer matching network design

    The best way is to export your layout design from other tools ( I am assuming you are using Cadence virtuoso) to ADS using GDS file and in ADS layout use Momentum ( method od moment based solver) or...
Results 1 to 25 of 80
Page 1 of 4 1 2 3 4