Search:

Type: Posts; User: kripacharya

Page 1 of 20 1 2 3 4

Search: Search took 0.04 seconds.

  1. Closed: Re: ELECTRICAL AND ELECTRONICS Instrumentation

    Interesting. So you're saying that a PMMC only measures Avg current? Good to know. Learn new stuff everyday.
  2. Closed: Re: ELECTRICAL AND ELECTRONICS Instrumentation

    Another one !! It's 11.125 amps.

    Please send prize directly to my home address.
  3. Replies
    24
    Views
    531

    Re: Transformer and alternator

    So you AGREE that it's an animation. Like Donald Duck Or Tom n jerry. Point 1 to me.



    In an animation anything is possible. Are you saying it might be ice cream? Never seen black ice...
  4. Closed: Re: ELECTRICAL AND ELECTRONICS Instrumentation

    LoL.. !
    I did that especially to confuse you. :wink:

    - - - Updated - - -

    Rajasekharn... Please post more puzzles like this. It will keep us awake at nights.
  5. Closed: Re: ELECTRICAL AND ELECTRONICS Instrumentation

    Actually you're right. I used 4 instead of +/- 4. So 4.828 is correct.

    - - - Updated - - -
  6. Closed: Re: ELECTRICAL AND ELECTRONICS Instrumentation

    KlaussT !!!!! :lol:

    First and foremost - the equation given is for current I, not voltage. So resistance is irrelevant.

    Second, the sinewave component requires rms calculation, but not the...
  7. Replies
    24
    Views
    531

    Re: Transformer and alternator

    Okay, let's discuss point by point then.
    1) It's Not really a 'simulation', it's more a graphical representation

    Do you agree?

    - - - Updated - - -

    Next..
    2) Those black/ yellow squares...
  8. Closed: Re: ELECTRICAL AND ELECTRONICS Instrumentation

    Yay. I pass. What's the prize ?? :grin:
  9. Closed: Re: ELECTRICAL AND ELECTRONICS Instrumentation

    Should be about 3.414 amps. Unless this is a trick question?
  10. Replies
    7
    Views
    242

    Closed: Re: Soldering on Battery Terminals

    I would think that epoxy/ graphite method would add several ohms to the current path. Obviously not desirable for a voltage power source, but may be the easier hence better route to take for some...
  11. Replies
    24
    Views
    531

    Re: Transformer and alternator

    I already did. See my post #16
  12. Replies
    24
    Views
    531

    Re: Transformer and alternator

    Blades of magnetic flux?
    Twelve magnets?
    Zeropoitnflux?
    What's a 'poitn'?
    Where's the North/South poles? Or is it all monopoles?

    Not really a 'simulation', it's more a graphical...
  13. Replies
    1
    Views
    89

    Closed: Re: Unexpected Chip identifier atmel

    There are two obvious reasons why this might happen--
    1) a mismatch between the cpu cofigured in your ICE setup and actual cpu on the target board.
    2) some fault in your connection between ice...
  14. Replies
    9
    Views
    254

    Closed: Re: Simple remote led stay on

    I repeat once again. One, or some of your buttons are bad.
    2nd possibility is that ba5104 is bad, but that is unlikely.
  15. Closed: Re: how to set and reset pin in microcontroller

    Ok. Let's assume your timer generates interrupt every 100mS.
    Now declare a variable as Int or Word (I.e. 16 bits) named Counter.
    Declare another variable as 2-hour-flag.

    In your 100mS isr,...
  16. Replies
    16
    Views
    2,415

    Closed: Re: solve the problem of noise

    You are assuming that relay switching etc is causing your interrupt to occur.

    This assumption itself is probably wrong.

    Please give details of your INT1 setup. Is it edge triggered? Positive...
  17. Replies
    3
    Views
    436

    Closed: Re: interrupt or rtos in microcontroller

    Rtos is useful when you have many complex realtime events occuring and the 'simultaneous' nature of processing is important.

    In your case you have just a very few realtime events and actions. You...
  18. Replies
    16
    Views
    598

    Closed: Re: High Frequency using 8051

    'Perfect' square output you will only get with resistive load. With inductor it will be different.
  19. Closed: Re: Why so many packages for Microcontrollers

    Which 'same' controller in different packages are you referring to? Give one example so we can discuss the reasons properly.
  20. [AVR]Closed: Re: New To Proteus 8 Professional with ATMEGA 328P

    You seem to have a single LED connected to 7 different I/o pins simultaneously. This is a strange setup.

    Please explain why this connection, and also post your code.
  21. Replies
    9
    Views
    254

    Closed: Re: Simple remote led stay on

    So what did you see ?
  22. Closed: Re: [Microcontroller] Voltage Reading without ADC

    A comparator would provide only a single set-point which could be monitored. I assume OP wants to linearly measure/ monitor entire range between 6v to 8.4v, where scheme outlined by @betwixt in post...
  23. Replies
    9
    Views
    254

    Closed: Re: Simple remote led stay on

    You look at the IR led through your camera viewfinder/ screen. If it is On or pulsing then you will see it as a purplish glow. Try it out on some other working remote !



    good



    But my...
  24. Replies
    9
    Views
    254

    Closed: Re: Simple remote led stay on

    As a guess, it is most likely that one of your buttons is malfunctioning.
    Check to see if the remote is also transmitting IR. You can do this by using a digital camera. If it IS on, then faulty...
  25. Closed: Re: Tuning of varicap diode in a magnetic loop antenna based on modulating signal

    I believe the real challenge here would be to ensure that your varicap/ magnetic loop IS tuned to the incoming frequency. There would be no 'feedback path' to correct for any errors.

    You could...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4