Search:

Type: Posts; User: betwixt

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds.

  1. Closed: Re: [PIC] Car Cooling System PSU Design Related

    Does your application permit charging one battery at a time?
    With some MCU intervention and some current steering it is possible to charge one at a time but you will not be able to use the '24v'...
  2. Closed: Re: [PIC] Car Cooling System PSU Design Related

    There is a clue in the MOSFET symbol about that!

    I can't understand why you need the 15V. If it is to charge the batteries you can't do it while they are in series, you need >24V to do that.
    If...
  3. Closed: Re: [PIC] Car Cooling System PSU Design Related

    Doesn't look at all right to me.
    I'm not sure what any of the circuit really does. D2 seems to have no purpose at all. If the DC-DC converter is to step down the PV voltage so it can charge the...
  4. Replies
    5
    Views
    259

    Closed: Re: problem with coding 123

    I understand that Klaus but it doesn't increase 10 bits to 12 bits, it just multiplies the result by 4, the LSB will always be zero. The ADC is still 10 bits.
    Some Arduino device can use 12-bit...
  5. Replies
    5
    Views
    259

    Closed: Re: problem with coding 123

    ... and what is the point in multiplying the result by 4? It is still a 10-bit value with zeroes at the end. It may be stored with extra bits but the precision isn't increased to 12-bits.

    Brian.
  6. Replies
    13
    Views
    490

    Closed: Re: MAR8 prior to AD8307

    Yes, but with the risk of damaging the meter and possibly the IC at higher signal levels. It isn't a safe strategy.
    A better approach if you want to follow that route is to amplify the lower voltage...
  7. Replies
    13
    Views
    490

    Closed: Re: MAR8 prior to AD8307

    If you add a capacitor at the output of the internal amplifier it may go unstable. Check the data sheet for the AD83xx device you choose, there is provision for a filter capacitor at one of the pins...
  8. Replies
    13
    Views
    490

    Closed: Re: MAR8 prior to AD8307

    It has a built in voltage amplifier so all you have to do is add a series potentiometer to limit the meter current. You would need a reference to adjust calibration accurately or apply a voltage...
  9. Replies
    13
    Views
    490

    Closed: Re: MAR8 prior to AD8307

    If you use a 100uA meter you can probably drive it directly from the AD83xx.

    Brian.
  10. Replies
    6
    Views
    302

    Closed: Re: How to create a voltage selector circuit

    I thnk a better topology is to feed your voltage to all the comparators in parallel but set a different threshold for each one. The will give you a 'bar graph' output with none, lowest, lowest and...
  11. Closed: Re: VU Meter only with 1LED (PWM) no IC except for OPAMP

    You can't use the outputs of comparators directly because all you get is an on/off indication of the instantaneous level. You would see the output flash at the frequency of the audio instead of its...
  12. Closed: Re: VU Meter only with 1LED (PWM) no IC except for OPAMP

    Not PWM, what you need is an op-amp as a gain stage, a rectifier (either diode or better still an op-amp based precision rectifier) to give you a DC level proportional to the sound level. Then you...
  13. Replies
    14
    Views
    461

    Closed: Re: Simple 50R I/O RF attenuator (1-30MHz)

    Just a thought - it is possible to use pre-set potentiometers with plastic center 'screws', either a slot or hex hole? You won't get perfect matching but you might get something close enough if you...
  14. Closed: Re: Rectifier diodes with bypass capīs & gounding speaker basketīs

    Based on what we have already said, Carbon dioxide resistors would be best but you might have trouble soldering to them. :)

    Really, the snubber circuits are not going to make one iota of...
  15. Closed: Re: ACS710 - pin 1 to 8 is shorted all together

    They are internally connected together through a copper loop so they should measure as shorted.
    The load current (or a proportion of it) passes through those pins and the internal circuits measure...
  16. Replies
    7
    Views
    367

    Closed: Re: Inrush current limiter

    A cheaper alternative might be a low-Q inductance in series with the incoming power. Something like a 50 - 100uH choke with a ~22 Ohm resistor across it. The inductor will slow the current rise and...
  17. Replies
    2
    Views
    209

    Closed: Re: specific use of volatile keyword

    Volatile would be a hint to the compiler to re-read the variable because it could have been changed by the ISR. For example, if your main code was counting 'x' upwards and your ISR changed the value...
  18. Replies
    7
    Views
    367

    Closed: Re: Inrush current limiter

    Most components are rated to handle higher current for brief periods so I doubt any damage would occur in any case.
    There are methods to limit the charge current to a capacitor but if the load is...
  19. Replies
    7
    Views
    367

    Closed: Re: Inrush current limiter

    ... and your thermistor tries to drop 2.5 * 10 = 25V as well.

    First explain what you mean by "it produces sparks" as this is nothing to do with inrush current.

    Brian.
  20. Replies
    7
    Views
    389

    Closed: Re: Building Blocks on an FM Band Receiver

    As per FvM, don't confuse FM and AM bandwidth requirements. The deviation of standard FM broadcasts is far wider than the bandwidth of normal 455KHz filters so you would 'chop off' most of the band...
  21. Replies
    7
    Views
    389

    Closed: Re: Building Blocks on an FM Band Receiver

    Before going further - when you say "FM Band" you seem to be referring to the domestic VHF broadcast band (~87MHz to 108MHz) where relatively wide band transmissions are used but the block diagram is...
  22. Closed: Re: Converting AF oscillator to use discrete components

    I'm not sure Brad's schematic is a true Wien-Bridge design as it uses different RC values in the series and shunt arms of the feedback loop and it also has additional phase shifting between the...
  23. Replies
    15
    Views
    817

    Closed: Re: Implementation of sine cosine using LUT

    You are quite right to correct me FvM - put my mistakes down to old age.

    They say your memory goes first ...... and I can't remember what comes second.

    Brian.
  24. Closed: Re: Rectifier diodes with bypass capīs & gounding speaker basketīs

    Perhaps they need one of these: https://www.ttvjaudio.com/The-Ultimate-Electrostatic-Headphone-Set-up-p/hif1230008.htm
    Thankfully it has free postage or it would be too expensive for me.

    On...
  25. Replies
    6
    Views
    482

    Closed: Re: tda7052a audio amplifier

    First thing to check is whether you really have a controllable volume at all. There are three type of TDA7052, the original with no letter at the end does not have electronic volume control at all....
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4