Search:

maybe a part designed to do what you want
rather than forcing a square peg into a round hole

if you want to build this, you'll need to add a variety of hardware to make it work
including high...

the rising edge of the LT1243 clocks the DFF, s both transistors "switches" are on at the same time -
one turning on and one turning off

shouldn't QQQ and QNOT go to the switch controls, SSS and...

in post 1, its a^7, in post its x^6 ?

the number of roots is equal to the highest exponent, so 7 roots and 6 roots, receptively

if all you want is a solution, then use Wolfram Alpha
type in...

please show how you want to connect/use the D FF

i expect you'll need to connect the current sense

i would suggest a half bridge controller, maybe even with a high side driver built in
maybe...

current path through IGBTs looks ok

data sheet page 3:

Sensor Input Measurement range (typical) +/- 3.6g

Sensitivity (typical) 300 mV/g

Zero g Bias Level (typical) 1.5 V

These tell me that an output of 1.5 V means no...

the surge protector will make a difference only if one or more of the MOVs are bad (low resistance or shorted)

are you using the same 24VAC 1A plug pack at home and at the "bad" location?

if...

"The 3A DC to DC converter keeps shutting off due to the thermal over load protected being triggered."

what is it designed to use as input?
check that the bad location has that input

I blew...

assuming your device has a power input and return, you can measure the voltage across those inputs
to measure the current, you need to disconnect the return and put in a resistor and measure the...

see this thread components are stick together in pcb document
it started on November 12

did you google ANSYS Medini?

in post 4, you said there are 10 identical digital blocks your LDO regulator is powering

if you have the current waveform for one digital block, since it isn't DC, use RMS to find a measure of...

I would size this LDO pass element depending on desired Vout, say 5V, drop out voltage, say 1V, so i need at least 6 V in
the current requirement has to be the maximum current the load will draw....

now that its not summer, is it working ok?

the water cooling idea works if the case is sealed for water
you may want to look out for condensation inside if the water cooling is cool enough,...

so 108MHz/107+1 translates to 108MHz/108 ?
if so, just use 108, not 107 + 1

if it isn't 108MHz/108, then it looks like (108/107) + 1 = 1.00934 +1 = 2.00934 ?

108 MHz / 2.00934 = 53.7488 MHz...

i see two possibilities

by touching the enclosure, you have somehow reduced the pressure and so the current goes down
0.04 mA is likely well within the design margins of the pressure transducer...

in the absence of a schematic, i assume the the load is in series with the resistor in series with the battery
therefore, your circuit looks like a battery with two resistors, all in series

the...

first, put it in the shade

then put a fan on the hot spot
there is some spot somewhere on the case that is warmer than the rest.
it may not be easy to find, so put a fan on it

put it on some...

kindly show the entire schematic

the missing stuff to the right likely has a connection for Isense
that will aid in answering your question

i am not an expert in geophysics, atmospheric physics, ocean chemistry and physics etc etc
and i doubt you are

i have yet to hear from any source that the sun is behaving differently in the last...

i am not very familiar with STM32F767



please explain notation 108-1 and 2-1 in
calculation prescaler should be 108-1, and a counter period 2-1.

please explain your calculation that got you...

i do not understand your notation

please explain M/M/1/infinity?
and for completeness sake, please explain "includes AVG. waiting and no. of customers ? "

i do not see a question

it might be less expensive to buy a power supply
it will certainly be less time consuming, especially if you include the time and effort already put in.

try a pearson current transformer

https://www.pearsonelectronics.com/products/wideband-current-monitors