Search:

Type: Posts; User: KlausST

Page 1 of 20 1 2 3 4

Search: Search took 0.13 seconds.

  1. Closed: Re: Where to get schematics about SCRs full-wave triggering circuits ?

    Hi,

    You still repeat not to strictly follow the recommendations.
    You modify the circuit, you modify the part values...
    1) May I ask why you used 1k instead of the recommended 10k?
    You say you...
  2. Closed: Re: Where to get schematics about SCRs full-wave triggering circuits ?

    Hi,


    I clearly talked about the "resistor to measure the current" and wrote it should be not higher than 10 Ohms.
    * but you removed all the other resistors
    * and the value of the current...
  3. Replies
    6
    Views
    183

    Closed: Re: water flow detection in a pipe

    Hi,

    good idea, Brian.

    Speed of sound in water is about 1500m/s.
    if there is water flow, then in one direction the speed of water flow adds to the speed of sound, in the other direction the...
  4. Closed: Re: Need help for ADS equation reprentation...

    Hi,

    My hint:

    dBm refers to 1mW.

    Now you want to refer it to the voltage on a 50 Ohms resistor.

    This leads to the question: How much voltage on a 50 Ohms resistor do you need to cause 1mW?
  5. Closed: Re: Where to get schematics about SCRs full-wave triggering circuits ?

    Hi,


    Yes, luck. Sadly luck, because it seemed you forgot all we tried to teach you.

    Designing electronics has nothing to do with luck. It´s learning, understanding, reading and calculating. ...
  6. Replies
    6
    Views
    183

    Closed: Re: water flow detection in a pipe

    Hi,


    Yes, for sure. Everybody wants this. :-)

    Then it's time to invent it. Do you have an idea?

    Let's say I have an idea, then I need a partner for marketing and selling, because I'm a...
  7. Closed: Re: Where to get schematics about SCRs full-wave triggering circuits ?

    Hi,


    From post#55:

    But you inverted both!

    Regarding the resistor to measure the current.
    The resistor value should be low, low enough not to influence the function of the circuit.
    A usual...
  8. Closed: Re: Enable circuit for backup battery boost converter

    Hi,

    Add two resistors an NPN BJT.
    Two resistors as voltage divider from 8V
    Center of divider to bjt_base
    Bjt emitter to GND
    Bjt collector to Boost_EN

    Klaus
  9. Closed: Re: how to select capacitor for ruhmkorff coil?

    Hi,


    The voltage of the capacitor is also limited by the available energy.
    E = 0.5 × V × V × C --> V = sqrt( 2 E / C)

    When the energy comes from a coil, then E = 0.5 × I × I × L

    Klaus
  10. Closed: Re: PIC16F877 interface with ds1307 ...RTC running 10 sec slow

    Hi,

    Honestly, I see absolutely no use in simulating the accuracy of an RTC.
    Simply trust the datasheet. The datsheet specifications should be more reliable than any simulation.

    And even if the...
  11. Replies
    2
    Views
    191

    Closed: Re: Voltage drop using 1 MOS

    Hi,

    You mean a MOSFET?
    N-channel or P-channel?

    Draw a schematic (hand drawn) of your idea.
    What does "it doesn't work as expected" exactly mean?
    Show us the test setup.
    And what is your...
  12. Closed: Re: How to convert CMRR in DB to Numerical Value

    Hi,

    What about doing an internet search on your own: "online dB calculator"...

    Klaus
  13. Replies
    9
    Views
    460

    Closed: Re: Circuit with an integrated FLIP FLOP

    Hi,

    "my first approach" of post#3 should give all you need to know.

    If not, then do an internet search with the given informations.

    Klaus
  14. Replies
    1
    Views
    169

    Closed: Re: BMS Circuit design using a BMS IC.

    Hi,

    All we could do is an internet research...the only useful information we have is "10S" or "20S".

    So it's a rather unelaborated question.

    So my expectation is that people spend their...
  15. Replies
    20
    Views
    759

    Closed: Re: ST7036i and mikroc STUCK

    Hi,

    If I had to debug it I'd use a scope to see the signals.
    With it you exactly see the signals on the bus...you are able to detect software problems as well as hardware problems.

    Hardware...
  16. Replies
    5
    Views
    403

    [PIC]Closed: Re: interfacing 74HC4051 with pic18f4550

    Hi,


    There is no best solution.

    * no free pins at all
    * internal pullup / pulldiwn
    * programmable pullup / pulldown
    * keeper
    * external pullup / pulldown
  17. Closed: Re: computer parallel port external relay control

    Hi,

    The only question of post#1 is


    Klaus
  18. Replies
    12
    Views
    362

    [AVR]Closed: Re: Temprature sensors. LM35 vs MCP9700

    Hi,

    my recommendation: Read the datasheets. Both datasheets specify accuracy.
    At least this is the way I`d do it.

    Klaus
  19. Replies
    9
    Views
    460

    Closed: Re: Circuit with an integrated FLIP FLOP

    Hi,

    can you please draw a truth table,

    your 1) violates your 2)
    --> I assume: when pinA = 1 and pinB = 1: do nothing = hold mode = no change

    your 2) is O.K.

    your 3) reduces to: when...
  20. Replies
    5
    Views
    286

    Closed: Re: Bootstrapping with Opto Driver

    Hi,


    This all makes no sense to me.

    --> Show a sketch/circuit about your idea.

    Klaus
  21. Replies
    5
    Views
    286

    Closed: Re: Bootstrapping with Opto Driver

    Hi,

    This circuit makes more sense:

    It differs to the first one:
    * Now there is no capacitor beween A nd C of the LED. It is between pin2 and GND. Mind the junction dot.
    * It seems to be a low...
  22. Replies
    5
    Views
    286

    Closed: Re: Bootstrapping with Opto Driver

    Hi,

    this is an inclomplete circuit. I don´t think it is correct. It does not make sens to discuss abut an incomplete circuit.

    Where is it from? --> give a link ..
    and give full description.
    ...
  23. Closed: Re: Where to get schematics about SCRs full-wave triggering circuits ?

    Hi,



    As already mentioned: You don't measure the gate current.
    --> If you want to know the gate current, then measure the gate current.

    And we don't talk about steady current, we talk...
  24. Closed: Re: Where to get schematics about SCRs full-wave triggering circuits ?

    Hi,

    well done :-)


    1) typical with SCR and triacs. The gate needs some current to trigger, the diac needs some voltage to trigger, the capacitor needs some time to charge....
    2) It´s no...
  25. Closed: Re: Where to get schematics about SCRs full-wave triggering circuits ?

    Hi,



    Yes, for sure. It does what it should do. It measures the voltage at the given node with respect to GND.
    If you want to measure the voltage across the load, then you have to measure one...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4