Search:

Type: Posts; User: andre_teprom

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Closed: Re: Does PIC16F18856 work if centre pad is left floating?

    From my previous experience with another Microchip's relative of the PIC16F's family, even forgetting to route one of the side pins of a DIP package, this was enough for the microcontroller to not...
  2. Closed: Re: Unable to read data from RTC DS1307 using Atmega8 and mikroc.

    Thanks for the warning, I will correct the code suggested above.
  3. Closed: Re: ESP8266EX based wifi module does not respond on any AT commands ( E103-W01-IPX)

    No, this library is used to make ESP8266 module connect to Wifi network from a board which has a bootloader already programmed there (Arduino, on this case). First you need to setup your Arduino IDE...
  4. Closed: Re: Unable to read data from RTC DS1307 using Atmega8 and mikroc.

    Just to let you know: Soft_I2C_Init() has a different purpose, it is intended to enable the I2C bus from microcontroller`s (master) side, whereas RTC_init() would enable the DS1307 (slave) throught...
  5. Closed: Re: Identify capacitor with marking code L62 104

    Who mentioned that? Datasheet? Mark code?

    Review post #2:
  6. Closed: Re: Unable to read data from RTC DS1307 using Atmega8 and mikroc.

    In the line 125 there is this function, disabled:


    //RTC_Init();

    Which certainly should be some routine for checking and ensuring that the clock would be always running, by resetting bit 7 of...
  7. Replies
    4
    Views
    295

    Closed: Re: NodeMCU ESP-32S pitch

    If you have these boards in hands, why not you measure them? By the way, at least with the ESP32 relative, the ESP8266, there are a number of NodeMCU's variants from many manufacturers, therefore in...
  8. [SOLVED]Closed: Re: LM741 Amplifier not working with IR2110 IC [PROTUES]

    With the above value at VDD of IR2110, the HIN pin allows input varying from approximately 0v to 12v, but the 741 has differential supplies ranging from -10v to +10v.
  9. Closed: Re: how to design a thermostat without Microcontroller?

    So far you do not seem to have done any more detailed analysis of the physical plant, as was proposed on the first page of this thread where the possibility of a less abrupt control (eg PID) was...
  10. Closed: Re: Unable to read data from RTC DS1307 using Atmega8 and mikroc.

    I can't see in your code the 7th bit of Address 00h (CH) being set anywhere, which should be done at least once after DS1307 got powered. It is responsible for effectively starting the RTC...
  11. Replies
    2
    Views
    163

    Closed: Re: hex code to Assembly

    Yes, this is called disassembling; there are tools for many compilers, make a search by yourself on the web.
  12. Replies
    3
    Views
    202

    Closed: Re: AD9288 is not working in Proteus

    There is no code on this attachment, of if there is somehow embeeded in the project file, not everybody has this program.
  13. Re: Help unlock microcontroler atmega644pa-mu

    Fuse bits are designed to protect microcontroller contents from unauthorized copy, therefore it is just acting as expected. However, if you want to not waste this chip by uploading another code...
  14. Closed: Re: Setting Counters and ISR Timer Interrupt in Arduino

    Since Arduino is a platform that must be compatible with several microcontroller architectures, the standard features are in fact tight facing to all ressources that each specific core have. If the...
  15. Replies
    24
    Views
    659

    Re: Transformer and alternator

    This thread became unfruitful and moods have been exalted again although ads-ee requests for avoiding that, so it will be closed.

    Fact: The mentioned video does not represent an actual simulation,...
  16. Replies
    2
    Views
    182

    [SOLVED]Closed: Re: Sleep mode - dspic33ch128mp508

    Didn't you find anything on instructions set of the compiler datasheet like that ?


    sleep();

    With a quick search on the Web I could easlily find the assembly instruction that do the same:

    ...
  17. [SOLVED]Closed: Re: ADC reading , Timer interrupt - dspic33ch128mp508

    Don't seem it is likely missing something like that at the init routine?


    INTCON2.GIE = 1 // enable global interrupt

    Seriously speaking, take a look at other extensively available examples on...
  18. [SOLVED]Closed: Re: ADC reading , Timer interrupt - dspic33ch128mp508

    It seems like you are missing the command for starting the A/D conversion, either at the main() and at the interrupt() vectors:


    ADCON3Lbits.CNVRTCH = 1;

    Moreover, you are not enabling...
  19. Closed: Re: PIC microcontroller debugging- dspic33ch128mp508

    You did not specify what programmer you are using, and what pins are aavailable to programming connector, anyway if I were you I would investigate this line:


    #pragma config JTAGEN = OFF // JTAG...
  20. Closed: Re: [Microcontroller] Voltage Reading without ADC

    From what was posed so far, indeed not clearly, it is assumed that OP wants to simply detect the battery low-level (supposedly lead-acid, given the above values), for which he certainly is not aware...
  21. Closed: Re: Tuning of varicap diode in a magnetic loop antenna based on modulating signal

    Should we assume that your doubt concerns an unconventional case of a demodulation without use of intermediate frequency in the receiver side? This feature is designed to allow the transmission of...
  22. Closed: Re: LoRa nodes and simultaneously communication with LoRa Gateway

    Collisions are not intrinsically handled with LoRa protocol, which means that proper packet management have to be externaly done by end application at each node in order to ensure that all command...
  23. Closed: Re: Is it possible to assign a value to a signal in a systemverilog assertion?

    This is a regular statement on this language.
  24. Closed: Re: Deadband and Hysteresis values from graphs

    The above 3 graphics are on different scales, so in order to make things easiest to understand I put everything on the same grid.

    For the first case there is neither deadzone nor hysteresis, there...
  25. Closed: Re: Does it exist an AC to AC converter in small package for converting 220v to 110v?

    No, this was not the point, but rather to advice OP about the correct value of the absolute maximum firing angle to be adopted in the design of the control circuit, just that.

    BTW, some fans have...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4