Search:

Type: Posts; User: FvM

Page 1 of 20 1 2 3 4

Search: Search took 0.36 seconds; generated 32 minute(s) ago.

  1. Replies
    22
    Views
    687

    Closed: Re: Bias current sensor for floating earth

    U2 LED reversed, but I see what you mean.


    You should know. If circuit isolation is a safety feature, your present design may also conflict with essential standards, e.g. IEC 61010 or other other...
  2. Replies
    6
    Views
    254

    Closed: Re: Phase detector with synchronous logic (FPGA)

    The 50 us limitation wasn't mentioned yet. In this case, "processing the entire dataset" is in fact more promising. Question is if you know the exact frequency beforehand or need to extract it from...
  3. Closed: Re: 14 bit adc output to 5 bit data conversion in VHDL

    May be the question is that trivial, may be some specific coding is intended. The OP missed to ask a clear question.
  4. Replies
    6
    Views
    254

    Closed: Re: Phase detector with synchronous logic (FPGA)

    The multiply idea sketched in post #1 is basically good, but it should be extended to I/Q demodulation to work over 0 to 360 degree. You can either generate a 90° delayed copy of one input signal,...
  5. Replies
    4
    Views
    205

    Closed: Re: transfer function of sc amplifier

    May be mathematically correct, but wrong in Z transform context.
  6. Replies
    22
    Views
    687

    Closed: Re: Bias current sensor for floating earth

    Don't think so. U1 LED is driven with wrong polarity and has negative transistor supply.

    157827

    Many previously mentioned problems are still present, ignoring balanced ground fault, huge...
  7. Replies
    11
    Views
    582

    Closed: Re: how to generate 4MHz clock from 2 MHz clock.

    A bit more complex. You'll design a kind of software PLL with 2 and 4 MHz output, locked to the 2 MHz reference. Dynamic phase shift might be used if the phase jitter requirements are very strict....
  8. Replies
    2
    Views
    140

    Closed: Re: Non-Invasive High Voltage Coupling?

    High Voltage Coupling means what, exactly? Measuring current, voltage, linearly, which range? HCPL-0370 reference suggest you want to compare current magnitude with a threshold, if so, what's the...
  9. Replies
    4
    Views
    265

    Closed: Re: 72 pin SIMM pinout and circuit

    If you experience contradicting hearsay specs, why not refer to major manufacturers datasheets instead?
  10. Replies
    56
    Views
    1,220

    Closed: Re: how to boost microvolts to higher voltages?

    I believe, you either don't read the answers or don't understand it. I have no other explanation for seeing the circuit in post #45 that has been already recognized as non-working. If you want to...
  11. Replies
    3
    Views
    197

    Closed: Re: Impedance calculation in CMOS circuit

    Incomplete problem description results in ambiguous or useless answer. At least one unclear point is floating substrate nodes.

    Transconductance is a small signal quantity, respectively it's valid...
  12. Replies
    4
    Views
    205

    Closed: Re: transfer function of sc amplifier

    1/2 sample period is no meaningful quantity in sampled data system. Output is only observed at integer multiples of sampling period. You'll see if you cascade two of the shown stages. What's the...
  13. Replies
    22
    Views
    687

    Closed: Re: Bias current sensor for floating earth

    A symmetrical fault example, referring to your previous design. How would you detect it?

    157803

    - - - Updated - - -


    The file is different from posted schematic (incomplete). The new scheme...
  14. Replies
    56
    Views
    1,220

    Closed: Re: how to boost microvolts to higher voltages?

    I feel that some points should be sorted out.

    You have been originally asking how to amplify µV signal to mV, with minimal supply voltage.
    Later you switched to 1.45 V input voltage and 8V...
  15. Replies
    22
    Views
    687

    Closed: Re: Bias current sensor for floating earth

    The idea of an ungrounded network (IT network) is to avoid short circuit currents in case of a single ground fault while being able to detect the fault.

    The 10 k resistors in your circuit cause a...
  16. Closed: Re: RHP poles always appear in my designed amplifier

    A RHP pole in the open loop transfer function can be only generated if the feedforward turns into positive feedback, likely to happen for the post #1 circuit.

    How do you measure the transfer...
  17. Replies
    22
    Views
    687

    Closed: Re: Bias current sensor for floating earth

    Your monitor circuit is generating huge leakage currents and power dissipation and surely no acceptable IMD solution.

    What is your of insulation resistance threshold specification?

    - - -...
  18. Closed: Re: Waveform saving upon trigger in windows from Oscilloscope

    MSO2000B series has 1M data points memory, about 10 sec @ 100 kSPS. Timebase can be set up to 100 s/div, 1000 s total length with respective lower time resolution. Not sure if quasi continuous data...
  19. Closed: Re: Waveform saving upon trigger in windows from Oscilloscope

    The simple way to save the waveform is to set up acquisition parameters as required, make a measurement and save the waveform to USB drive in *.csv format. No software needed.

    It should be noted...
  20. Replies
    23
    Views
    661

    Closed: Re: Flyback Airgap Doubts?

    In case you want someone to check your transformer design, you should give complete information, e.g. which input voltage was used during the test. Also what's the designed primary peak current.
  21. Replies
    3
    Views
    199

    Closed: Re: Circuit to capture the motor inrush current

    Inrush current can be captured with a current probe and a digital oscilloscope.

    It's not clear what you exactly want to achieve and how the schematic is related to motor inrush current. ...
  22. Replies
    11
    Views
    582

    Closed: Re: how to generate 4MHz clock from 2 MHz clock.

    Possible solutions have been sketched, but the application requirements are yet unknown.
  23. Replies
    22
    Views
    687

    Closed: Re: Bias current sensor for floating earth

    IMD (insulation monitoring devices) are specified by IEC 61557 and available on the market. For unearthed (IT) power supplies, these devices are basically implementing the operation principle...
  24. Replies
    11
    Views
    582

    Closed: Re: how to generate 4MHz clock from 2 MHz clock.

    10 MHz minimal clock input frequency is common series 7 MMCM spec as far as I'm aware of.
  25. Replies
    11
    Views
    582

    Closed: Re: how to generate 4MHz clock from 2 MHz clock.

    If you have a higher frequency clock available, a digital PLL can generate the 4 MHz clock, however limited to the time resolution of the system clock. Ultimately, you can phase lock an auxiliary...
Results 1 to 25 of 499
Page 1 of 20 1 2 3 4