Search:

Type: Posts; User: FvM

Page 1 of 20 1 2 3 4

Search: Search took 0.33 seconds.

  1. Replies
    2
    Views
    216

    Closed: Re: External Antenna on Bluetooth module

    CSR8635 has 50 ohm RF port, the modules have additional matching circuit for the meander antenna.
  2. Replies
    5
    Views
    198

    Closed: Re: Help identify the item

    By looking at the circuit, it should be rather easy to determine if it's a passive component or a transistor. Although this is a typical RF transistor package, it could be also a fixed RF attenuator.
  3. Closed: Re: ACS722 Hall sensor IC...minimum loading for output signal voltage pin?

    You have asked the same question before, and it has been answered....
  4. Replies
    5
    Views
    184

    Closed: Re: Differential pair with dynamic resistance

    You new schematic doesn't even give a value for Rc. How could we answer?

    As previously mentioned, saturation occurs above a certain value of Rc. Usually, saturation would be avoided. But it's not...
  5. Replies
    6
    Views
    201

    Closed: Re: higher output frequency with PCA9685?

    The maximum PWM frequency is actually fclk/(4*4096), there's an additional prescaler.
  6. Replies
    6
    Views
    216

    Closed: Re: Pulse power dissipation in a BJT

    I see that medium power transistors like FMMT495, MMBT5550 or BCX41 have apparently sufficient thermal capacity to handle the requested pulse load, under the prerequisite that the average power can...
  7. Closed: Re: Sampling Bandwidth vs. Bandwidth in Tracking Mode of a Sample/Track and Hold

    I doubt that both terms have clearly commonly understood definitions. The original post is apparently referring to a paper or datasheet. If so, why don't you quote the definition therin.

    It's more...
  8. Replies
    6
    Views
    216

    Closed: Re: Pulse power dissipation in a BJT

    10 ms is much too long for the small thermal capacitance of low power SOT23 transistor, e.g. BC847. A medium power transistor in SOT23 with larger chip might work.
  9. Replies
    5
    Views
    184

    Closed: Re: Differential pair with dynamic resistance

    T2 is not saturated with Rc=2k, only with 20k.
  10. Closed: Re: Waht is the name of ATX connector on motherboard?

    Molex Mini-Fit Jr series
  11. Closed: Re: How to trace the original of netlist gates back to the original RTL description

    Did you try to synthesize with different optimizer goals and timing constraints? A possible reason for increased power consumption could be that the synthesizer is duplicating gates to achieve timing...
  12. Closed: Re: Please help me avoid a disaster with my first pcb

    Processed copper thickness is the relevant parameter for trace resistance and current rating. Outer layer copper is build by electrolytic deposition on the etched base copper structure when through...
  13. Replies
    6
    Views
    400

    Closed: Re: Transformer winding, how to?

    If I understand right, you are trying to build a saturable reactor. The type shown in the first link can't be build on a single core. Sending current back forth through the bifilar winding has just...
  14. Closed: Re: Please help me avoid a disaster with my first pcb

    VCCIO is the 5V output of DCDC, I think it's o.k. to route it this way.
  15. Replies
    9
    Views
    825

    Closed: Re: USB protocol related queries

    I would immediately move the thread to ASIC section - if it had any ASIC related questions. But yet there are none. Please review your questions.
  16. Replies
    9
    Views
    825

    Closed: Re: USB protocol related queries

    I don't see a relation of your previous questions to ASIC design, it's neither mentioned nor obvious in any regard. The discussed problems, although a bit vague, are general USB topics. The...
  17. Closed: Re: Please help me avoid a disaster with my first pcb

    Not completely clear which net is addressed.

    Regarding the double side population, I understand that it can be only realized with hand soldering. The components placed on top of through hole pins...
  18. Replies
    9
    Views
    825

    Closed: Re: USB protocol related queries

    A mass storage device is operated with read and write to logical blocks, the file management is performed by the controlling computer. Interrupting a transaction in the middle involves a high risk of...
  19. Replies
    6
    Views
    337

    Closed: Re: Solving issues in my PCB grounding

    The SMPS is a Class I device, designed to be operated with proper proctective earth connection. The problem description suggests that the PE connection is missing.
  20. Closed: Re: Generating a digital pulse of 10 secs and 1 sec

    How about building a digital timer? Can be made in programmable logic, but also using a microcontroller or by assembling discrete logic ICs. All three variants will use a crystal oscillator if...
  21. Closed: Re: Def-Stan 59-411 proble with MOVs don't dissipate energy

    I wonder if the used MOV are actually rated for the applied DCS12 test signals, which are considerably different from industry standard surge test signals.

    But if the MOV survives, the problem is...
  22. Replies
    4
    Views
    502

    [SOLVED]Closed: Re: Op amp integrator formula

    No idea where you got the integral expression. I guess " ∫ t 0" is a garbled form of "integral from 0 to t", which would be the correct description of inverting integrator in time domain in contrast...
  23. Replies
    6
    Views
    530

    Closed: Re: water flow detection in a pipe

    Consider flow and pressure as independent parameters. Pressure is important for "invasive" sensors.

    0,015 m/s seems correct and is quite low. An arbitrarily selected 6" industry standard paddle...
  24. Replies
    23
    Views
    1,020

    Closed: Re: UC3845 ETD29 transformer PWM signal

    The ringing occurs in discontinuous mode when the rectifier current flow stops. It's a high impedance/low energy oscillation (frequency set by main inductance and sum of winding, transistor and...
  25. Closed: Re: Off-the shelf transformer for push pull converter

    Or referring to ∫Vdt (ET in your terminologie)
    I = ∫Vdt/L
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4