Search:

Type: Posts; User: KlausST

Page 1 of 20 1 2 3 4

Search: Search took 0.08 seconds; generated 40 minute(s) ago.

  1. Closed: Re: Higher Current Consumption than expected with AFE and embedded Flash

    Hi,

    As already said (and if not otherwise mentioned): close to VCC or close to GND.

    It is written in the datasheet, and I assume the IC manufacturers provide additional information about "low...
  2. Closed: Re: Higher Current Consumption than expected with AFE and embedded Flash

    Hi,

    Please confirm that at any time no pin is left floating, neither a used pin nor an unused pin.

    Usually input pins where the voltage level is not close to VCC or GND may cause increased...
  3. Replies
    4
    Views
    155

    Closed: Re: Li-ion Battery charger need help

    Hi,

    May I ask why you didn't read the datasheet?

    It is no Li-Ion, it specifies the charging method, it specifies the charging current, which is not 1C...

    Klaus
  4. Replies
    4
    Views
    155

    Closed: Re: Li-ion Battery charger need help

    Hi,

    What exactly does the datasheet say? 1C is typical or recommended charge current, or maximum charge current?
    (Why don't you post a link to the datasheet?)

    Doesn't the manufacturer provide...
  5. Closed: Re: How can I tell if my laptop screen is LED or LCD?

    Hi,

    There are laptops with OLED display.

    Thus I recommend to look into the operating manual of the laptop or consult the manufacturer's internet pages.

    Klaus
  6. Closed: Re: li-ion voltage reducer to 3volt - help needed

    Hi,

    There are linear LDOs.
    And there are switch mode step down converters, also called buck converters.

    All have their benefits and drawbacks.

    But to decide which one to choose, you need to...
  7. Replies
    26
    Views
    690

    [SOLVED]Closed: Re: IGBT Overshoot and Weird Slope

    Hi,

    There are electronic devices called capacitors.
    Do you know them?

    Klaus

    Added:
    Your schematic violates general rules how to use gate drivers as well as IGBTs.
    The same applies for the...
  8. Replies
    8
    Views
    262

    Closed: Re: Protecting SMPS against mains transients.

    Hi,

    Basically every overvoltage protection includes:
    * a serially connected device to limit the current (even wiring)
    * a parallel connected device to limit the voltage
    For sensitive devices...
  9. Closed: Re: Is it possible to make an IGBT to work at duty cycles up to 100%?

    Hi,

    I wonder why you still ask the same vague question.
    It is already answered that there is no problem in continously operating an IGBT. There is nothing special to take care of.
    All...
  10. Replies
    1
    Views
    142

    Closed: Re: Bldc Motor controller Mosfet Circuit

    Hi,
    I can not remember to have seen this circuits before...and I've seen a couple BLDC circuits.

    Then show us.
    If it's in "all" ... then I expect it to be in the application notes, too...and I...
  11. Closed: Re: PCB layout design consideration for BLDC controller

    Hi,

    Every Mosfet manufacturer and every gate driver IC manufacturer provides application notes and design notes. They are free. Use them.

    Klaus
  12. Replies
    20
    Views
    964

    Closed: Re: I2C not working properly

    Hi,

    Maybe a dumb question:
    When your I2C slave has no internal clock, then how can it generate 300ns (or more) delays?

    I2C_START condition: SDA_falling @ SCL_HIGH
    I2C_STOP condition:...
  13. Replies
    20
    Views
    964

    Closed: Re: I2C not working properly

    Hi,

    Whan I see your diagrams ... one thing is worrying me: the edges of the data sometimes are very close to the edges if the clock.
    They should not be that close.
    Are you sure they are...
  14. Closed: Re: Is it possible to make an IGBT to work at duty cycles up to 100%?

    Hi,


    I'm not surprised.
    100% duty cycle is nothing special, no stressing situation.
    It's rather the most "non stressing" situation for an IGBT....except "continously OFF".

    For this situation...
  15. Closed: Re: Is it possible to make an IGBT to work at duty cycles up to 100%?

    Hi,

    I wonder why you use that expensive driver circuit.
    It is designed for
    * high side switching
    * high speed switching
    * power supply
    * and a lot of other features that you don't need (at...
  16. Closed: Re: Is it possible to make an IGBT to work at duty cycles up to 100%?

    Hi,

    Every IGBT can work with 100% duty cycle.
    It's not a problem of the IGBT, it's a problem of the gate driver circuit.
    And only high side and only if a bootstrap supply circuit i)s used.

    As...
  17. Closed: Re: Flyback SMPS power MOSFET getting hot? uc3843 pwm converter

    Hi,


    It's not clear where your arrows point to..
    The "air gap" is between the two halves of the ferrite core. (With air gap, the two ferrite pieces don't touch each other).
    (It's not the gap...
  18. Replies
    45
    Views
    1,319

    Closed: Re: Driving 140x 3W LEDs

    Hi,

    I see a lot of misunderstandings.

    In the order of your post#37:

    The aim of the constant current is not to provide a precision constant current. The aim is to limit the current to a safe...
  19. Replies
    4
    Views
    264

    Closed: Re: layout design of an adapter using Altium

    Hi,

    My tablet can't open your attached file.

    Klaus
  20. Closed: Re: Testing LI Batteries with the help of a device

    Hi,

    You say you want test for "reliability". How do you test and evaluate reliability of LiPo cells?

    Why not buy a couple of these devices?

    Klaus
  21. Replies
    3
    Views
    186

    Closed: Re: H bridge with IR2110

    Hi,

    I don't understand what is shown on the scope and what signals these are on the schematic..

    But one thing I can say:
    Your analog circuit makes no sense.
    Buffering a signal .... then...
  22. Closed: Re: Implementation of a MUX for selecting from 2 different sets of inputs

    Hi,

    I agree with ads-ee.
    I really don't have a clue what you are talking about.

    Draw a sketch of what you want to build and give precise informations and specifications (usually with values...
  23. Replies
    21
    Views
    2,121

    Closed: Re: current excitation for sensor

    Hi,

    Maybe you mix accuracy with precision?

    You can't get 0.025% accuracy with all what you wrote before.
    Even 0.025% precision is hardly possible.

    And can you please explain how you want to...
  24. Replies
    4
    Views
    231

    Closed: Re: MP1584 5v regulator voltage drop problem

    Hi,

    Please try to give useful informations.
    * I can't find information about voltage drop in post#1.
    * Now we know that you are concerned about voltage drop. But we don't know how much (maybe I...
  25. Replies
    21
    Views
    2,121

    Closed: Re: current excitation for sensor

    Hi,

    What exactly (of the explanation) you need to be clarified?

    A voltage reference will not start at random voltages (why sould it in your eyes).
    But it will
    * drift with time
    * drift with...
Results 1 to 25 of 499
Page 1 of 20 1 2 3 4