Search:

Type: Posts; User: Mabrok

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Closed: Re: Microstrip to layout in ADS for power amplifier design

    The problem is when we do the fabrication. How transistor will be fit perfectly if its dimensions not defined?
  2. Closed: Re: Microstrip to layout in ADS for power amplifier design

    For the transistor, I am using CGH40010F provided by cree. They offer ADS model which can be used in the schematic window but it does not have a layout view in the layout window. So, Could you place...
  3. Closed: Re: Microstrip to layout in ADS for power amplifier design

    How to import the elements like transistor in the layout window? And also each element has specific dimensions to be fit perfectly during the fabrication process. How to control that? Are there any...
  4. Closed: Re: Microstrip to layout in ADS for power amplifier design

    Yes, right
    But can you please you explain more
  5. Closed: Microstrip to layout in ADS for power amplifier design

    Hi,

    Can the microstrip gap (Mgap) used as a replacement for lumped components and transistor when we want to convert the schematic to layout? Attached is the Mgap in the schematic window. Thanks...
  6. Closed: Out of band stability of RF power amplifier

    Hi,
    I have designed doherty power amplifier for 3.4-3.6 GHz band. After many optimization process, I get the required specifications. However, the simulation results show instability at 500 MHz to...
  7. Replies
    3
    Views
    271

    Closed: Re: RF Power amplifier stability

    I have added resistor in series and helped in enhancing the stability. but on the other side degraded the gain too much.
  8. Replies
    3
    Views
    271

    Closed: RF Power amplifier stability

    I have designed class AB Power amplifier for 3.4-3.6 GHz band. When i checked the stability, the amplifier was stable over the entire band (K>1). But for out of band at certain frequencies (0.5 to...
  9. Replies
    5
    Views
    439

    Closed: Re: Load pull simulation in ADS

    Thank you. In general case, for RF power amplifier design the device have to be stable from where until where? let's say that our required frequency band is 3.4-3.6 GHz.
  10. Replies
    5
    Views
    439

    Closed: Re: Load pull simulation in ADS

    Also I want to ask another question. For the amplifier stability, my amplifier is stable from 1 to 5 GHz, below 1 GHz is not stable, is that ok? (Note: the required frequency band for my design is...
  11. Replies
    5
    Views
    439

    Closed: Re: Load pull simulation in ADS

    Thank you for the valuable comments. For confirmation, is it correct that impedance at marker 3 is consider as the Zload, and input impedance is consider as the Zsource based on the attached image?
  12. Replies
    5
    Views
    439

    Closed: Load pull simulation in ADS

    Hi,

    In ADS load pull simulation results. Is it correct that the impedance at marker 3 is the Zload (7.161+j 2.480) which are using in output matching design, and input impedance is the Zsource...
  13. Replies
    5
    Views
    557

    Closed: Re: Power Amplifier Design

    Thanks for the valuable information. Is the same thing is considered for doherty sub-amplifiers (main & auxiliary)? I want to do a correct DPA design, but still confusing about load pull setting such...
  14. Replies
    5
    Views
    557

    Closed: Power Amplifier Design

    For load-pull simulation to extract optimum load impedance. How to set input power ? According to what?

    Thanks in advanced
  15. Replies
    3
    Views
    527

    Closed: RF Power Amplifier Design

    In power amplifier design. how to properly determine the biasing point of different classes such as class AB, Class C, and so on? How to do it through simulation using ADS?
  16. Replies
    2
    Views
    286

    Closed: Re: Amplifier layout in ADS

    Thanks for the information. How about the transistors and DC voltage sources and ground?
  17. Replies
    2
    Views
    286

    Closed: Amplifier layout in ADS

    How to get the correct layout for microstrip design in schematic of ADS? How to represent the transistor, DC voltage source, and the ground in layout and how to get the correct dimensions? kindly...
  18. Replies
    5
    Views
    489

    Closed: Re: Doherty Power Amplifier

    Thanks for the information. Do you have the idea about how to get I_carrier' & I_peaking through the simulation using ADS?
  19. Replies
    1
    Views
    245

    Closed: Broadband Power Amplifier design

    Is the design of power amplifier in the 3.4-3.6 GHz band consider as broadband? How to distinguish between wideband, broadband, and narrow band? Thanks in advanced
  20. Replies
    5
    Views
    489

    Closed: Re: Doherty Power Amplifier

    Thank you. These equations can be used to design real DPA (to be fabricated)?
  21. Replies
    5
    Views
    489

    Closed: Doherty Power Amplifier

    How to determine the impedance at combining node (Rcn) of doherty sub-amplifiers? Is it a standard for all DPA designs? Or depends on the design? Thanks in advanced154540
  22. Closed: Two-tone simulation of power amplifier design

    In the two tone simulation of power amplifier design, how much should be the spacing between the two tones? Thanks in advanced
  23. Replies
    2
    Views
    258

    Closed: Power amplifier impedance matching

    Is it possible to match complex impedance to other complex impedance using quarter wave impedance matching technique? And How?
  24. Replies
    0
    Views
    249

    Closed: Scaling factor in ADS

    How to find scaling factor in advanced design system (ADS) 2011?
  25. Replies
    1
    Views
    248

    Closed: RF Power Amplifier Design

    How to simulate Adjacent channel leakage ratio (ACLR) of Power Amplifiers?
Results 1 to 25 of 76
Page 1 of 4 1 2 3 4