# Search:

Type: Posts; User: srizbf

Page 1 of 20 1

1. ## Thread: Calculating electromagnet – magnetism vs heat

by srizbf
Replies
5
Views
103

### Closed: Re: Calculating electromagnet – magnetism vs heat

heating due to wire can be calculated by knowing the resistance of the wire wound and current passing through it.

for 20awg get the typical resistance from data sheet or measure it
and estimate...
2. ## Thread: Difference between Differentiators and Comparators

by srizbf
Replies
3
Views
163

### Closed: Re: Difference between Differentiators and Comparators

differentiators produce the differentiation of input signal waveform.
(i.e. d/dt of input signal)

comparator compares the voltages between the NonInv and Inv i/ps of opamp and produce a polarised...
3. ## Thread: Decoupling capacitor value

by srizbf
Replies
3
Views
291

### Closed: Re: Decoupling capacitor value

a feedthrough type of decoupling capacitor will bypass the noise in DC line.
4. ## Thread: What is this sensor? (Can detect the clap sound)

by srizbf
Replies
4
Views
326

### Closed: Re: What is this sensor? (Can detect the clap sound)

An eletret microphone.
5. ## Thread: NE555 astable frquency

by srizbf
Replies
10
Views
373

### Closed: Re: NE555 astable frquency

again a typo.

the term 'c' is left out in denominator.

so the freq is of the form:

1.44/((R2+kRv1)+(1-k)Rv1)C2
6. ## Thread: NE555 astable frquency

by srizbf
Replies
10
Views
373

### Closed: Re: NE555 astable frquency

frequency of your circuit is:

1/((R2+k*Rv1)+(1-k)*Rv1)

where 'k' as per figure is 0.41

- - - Updated - - -
7. ## Thread: Help wiring a Ne555 Timer delay module (monostable?)

by srizbf
Replies
9
Views
745

### Closed: Re: Help wiring a Ne555 Timer delay module (monostable?)

if you want the module to have a trigger input in monostable operation ,
trace the circuit in the board and modify it.
8. ## Thread: Help wiring a Ne555 Timer delay module (monostable?)

by srizbf
Replies
9
Views
745

### Closed: Re: Help wiring a Ne555 Timer delay module (monostable?)

The board does not have the option of separate trigger.
Switching ON of pwr supply generates the trigger internally.
9. ## Thread: Help wiring a Ne555 Timer delay module (monostable?)

by srizbf
Replies
9
Views
745

### Closed: Re: Help wiring a Ne555 Timer delay module (monostable?)

The board is not a faulty one. It may bes on the wiring diagram given.

Make an experiment . Just Connect Vcc and Gnd terminal to power supply .Dont connect any other load or switch.

See...
10. ## Thread: Connection Servo Motor to PC

by srizbf
Replies
4
Views
661

### Closed: Re: Connection Servo Motor to PC

you must give more information for getting some useful answers.
what sensor and its voltage/current spec and motor spec and details.

How do you propose to control from PC? Is there any package...
11. ## Thread: Ethernet software or terminal in windows for ZYNQ

by srizbf
Replies
5
Views
3,003

### Closed: Re: Ethernet software or terminal in windows for ZYNQ

Teraterm can be used for both uart and ethernet.

telenet is the mode.

yes. you must have telenet service on bothends.

both send and recieve from / to files.

data rate spec is not known as...
12. ## Thread: [Questa] How to colorize the Transcript window (files, directories, etc)?

by srizbf
Replies
2
Views
293

### Closed: Re: [Questa] How to colorize the Transcript window (files, directories, etc)?

try ls --color -la .
13. ## Thread: Ethernet software or terminal in windows for ZYNQ

by srizbf
Replies
5
Views
3,003

### Closed: Re: Ethernet software or terminal in windows for ZYNQ

telnet can store the recd data in file.
ZYNQ is the server and windows PC is client.
the trasferred data should be in file format .

if your ZYNQ cannot meet this then telnet cannot do it.
14. ## Thread: Ethernet software or terminal in windows for ZYNQ

by srizbf
Replies
5
Views
3,003

### Closed: Re: Ethernet software or terminal in windows for ZYNQ

windows contains a command 'telnet' or you can try

https://www.chiark.greenend.org.uk/~sgtatham/putty/latest.html

15. ## Thread: Creating a simple motor powered battery for use in clothing

by srizbf
Replies
7
Views
1,893

### Closed: Re: Creating a simple motor powered battery for use in clothing

one that you can consider is:
https://www.allelectronics.com/item/dcm-542/small-dc-gear-motor-3v-20-rpm/1.html

for the slow speed dc geared motor
you can search amazon also.
16. ## Thread: Creating a simple motor powered battery for use in clothing

by srizbf
Replies
7
Views
1,893

### Closed: Re: Creating a simple motor powered battery for use in clothing

Welcome to the edaboard!

Coming to your idea ,
since you want the motor to rotate slowly a geared Dc motor will suit your requirement. (other motors like stepper , servo etc can be used but with...
17. ## Thread: Synchronize comparator output with a clock

by srizbf
Replies
5
Views
1,171

### Closed: Re: Synchronize comparator output with a clock

whatabout a clocked D-FF with D input from comparator out and clock from your source?
18. ## Thread: First 555 timer circuit, bunch of questions using a relay

by srizbf
Replies
20
Views
5,479

### Closed: Re: First 555 timer circuit, bunch of questions using a relay

not advisable to keep trigger pin open(pin 2) .
connect a 10k resistor to supply Vcc and pin 2 . then pin2 with a push button switch to ground.

otherwise the behaviour will be random.
19. ## Thread: Does gyroscope requires calibration? (MPU 6050)

by srizbf
Replies
37
Views
3,173

### Closed: Re: How to convert accelerometer data into G with the ADXL345 digital accelerometer

Nothing wrong.
it indicates that the accelerometer may be stationary but is not perfectly vertical.
20. ## Thread: Does gyroscope requires calibration? (MPU 6050)

by srizbf
Replies
37
Views
3,173

### Closed: Re: How to convert accelerometer data into G with the ADXL345 digital accelerometer

in the +/- 2g range , the resolution is 10bits.
The value per bit is 3.9mg.(3.90625mg exactly).

multiply your axis reading with this constant to get g value.
21. ## Thread: How to determine voltage level on Pin 2 of the comparator

by srizbf
Replies
2
Views
868

### Closed: Re: How to determine voltage level on Pin 2 of the comparator

the current flowing through 0.22 ohm produces a drop which is compared with the Vref you set with R2 pot.

Based on the circuit given a rough calculation estimates the current to have a maximum of...
22. ## Thread: How to distinguish the electronic design approaches?

by srizbf
Replies
3
Views
319

### Closed: Re: How to distinguish the electronic design approaches?

whatever name it is called , the second approach is desirable of integrated transceiver and transmitter provided it meets your spec of signal sensitivity and SNR ratio and the output power...
23. ## Thread: Vision camera software programming

by srizbf
Replies
3
Views
1,438

### Closed: Re: Vision camera software programming

first phase is to have the pixel data of the image.

For that you must have the format of the image that your camera produce.

Read the datasheet of your camera and find the output format and...
24. ## Thread: Not able to fetch data from Energy meter

by srizbf
Replies
1
Views
1,854

### Closed: Re: Not able to fetch data from Energy meter

baudrate , databits , start and stop bit setting should match that of your sender(energymeter) . otherwise you will get
garbage characters .
25. ## Thread: Vision camera software programming

by srizbf
Replies
3
Views
1,438

### Closed: Re: Vision camera software programming

*get the (rgb pixels) data of the frame from camera.
*from the image data , use image processing algorithm do what you want like white detection...
Results 1 to 25 of 500
Page 1 of 20 1