Search:

Type: Posts; User: Sandeep.Lerio

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    2,445

    Closed: CloneZilla

    Hi Everyone,

    I'm trying to Clone M-systems DiskonChip (MD1150-D64) Module to Compact flash (SanDisk 1.0 GB) using CloneZilla. When I mount DiskonChip Module (DOM) to my computer it's showing as...
  2. Closed: Re: [Moved] M-System DiskOnChip Module MD1150-D64

    Unfortunately, No. So i'm looking for other methods
  3. Closed: Re: [Moved] M-System DiskOnChip Module MD1150-D64

    Actual In the above picture it isn't because I showed just picture without connection. Please have a look the below pictures which are connected.

    146371
    146372

    Let me know your comments @FvM
  4. Closed: Re: [Moved] M-System DiskOnChip Module MD1150-D64

    Hi FvM,

    Thanks for quick reply. Please have a look on image and let me know if connection is right or wrong?

    146369
  5. Closed: [Moved] M-System DiskOnChip Module MD1150-D64

    Hi Everyone,

    Any suggestions "How can I read and write DiskOnChip modules MD1150-D64 with PC"? I already installed Windows XP and connected via Sata to IDE. Unfortunately, PC didn't recognize....
  6. [General]Closed: Re: Analog Output interfacing with 5v microcontroller

    Thanks FvM,

    It help when I connected a 330ohm resister between pin 6 and 8 it shows the current varies between 0.0mA -1.36 mA. Now how to transfer this current to Arduino Uno? How does Arduino UNO...
  7. [General]Closed: Re: Analog Output interfacing with 5v microcontroller

    So, I need to connect a 500-ohm resistor between pin 6 and 7 to get 4-20mA current output? Without resistor, I tried earlier it showing only 4mA. But I will try with <=500 ohm resistor
  8. [General]Closed: Re: Analog Output interfacing with 5v microcontroller

    But How to read with Multimeter? Because, If I got the analog output reading on multimeter then I will connect those wires to the microcontroller. What do you think?

    Do you think I need to 500-ohm...
  9. [General]Closed: Re: Analog Output interfacing with 5v microcontroller

    Please see the attached files . And leave your reply
  10. [General]Closed: Re: Analog Output interfacing with 5v microcontroller

    Hello Everyone,


    I'm trying to get 4-20mA current analog output reading from the Pepperl+fuchs VDM 18-300 which PNP connection type. But I'm not getting. Do you know why?
  11. [General]Closed: Re: Analog Output interfacing with 5v microcontroller

    Sorry about Novice knowledge on electrical wiring. Are you sure it required an internal connection between "0V and Qa-" . Please see the attached picture and let me know about it.134302
  12. [General]Closed: Re: Analog Output interfacing with 5v microcontroller

    Thanks for reply everyone,

    I attached the wiring and more information. Please have a look and suggest me your views about it:bsdetector:
  13. [General]Closed: Re: Analog Output interfacing with 5v microcontroller

    Hi Ogulcan,

    Thanks for reply.I apologize for insufficient information on the data. I added manual and datasheet,
    Please have a look and tell me your suggesstions.

    134200
    134199

    I'm using...
  14. [General]Closed: Re: Analog Output interfacing with 5v microcontroller

    Hi KlausST,

    Thanks for reply. Here is link of the sensor datasheet
    http://www.pepperl-fuchs.com/global/en/classid_53.htm?view=productdetails&prodid=34337


    And I would like to interface with...
  15. [General]Closed: Re: Analog Output interfacing with 5v microcontroller

    Hello Okada,

    Thanks for reply. Yes, I check the voltage across 4-20mA output and It varies -22.34v to 22.34v. So, I Normally add 250Ω resistor used to get 1 to 5V measured across the resistor,...
  16. [General]Closed: Analog Output interfacing with 5v microcontroller

    Hello Everyone,

    This is my first post on this forum., Seems like there are a lot of rules in this forum.

    I have an analog output is 4-20mA industrial distance sensor. And I would like to...
Results 1 to 16 of 16