Search:

Type: Posts; User: FvM

Page 1 of 20 1 2 3 4

Search: Search took 0.25 seconds.

  1. Replies
    1
    Views
    130

    Closed: Re: ISO 6141, 6142 and 6143 ?

    The standards have nothing to do with detector design or operation. You can review the table of content at standard publishers.
  2. Replies
    3
    Views
    134

    Closed: Re: Replacement for AD848JR

    There's probably no exact replacement for this high speed OP. If I would suggest any, you'll surely tell me that it's neither available at your site.

    Instead you should analyze the detail...
  3. Closed: Re: Dimming the MP2489 right down to zero (Buck LED driver)

    The question is, why does the datasheet suggest minimal 1.25V control voltage for PWM operation? I see two possible explanations:
    1. They simply don't consider mixed analog and PWM dimming as useful...
  4. Closed: Re: IGBT Short Circuit Detection using Current sensing

    Implemented to avoid overvoltage when cutting high short circuit currents. The feature must be supported by gate drivers. ACPL-332x doesn't, so it's no option here.


    You should be aware of...
  5. Replies
    3
    Views
    185

    Closed: Re: Understanding the USB Protocol

    12 Mbps is the physical bit rate and always used in FS link, no matter what the transported payload is. You are looking for the net throughput which depends also on packet size and protocol overhead...
  6. Replies
    3
    Views
    185

    Closed: Re: Understanding the USB Protocol

    You want to read the class specification documents. CDC and HID don't use all transfer types, e.g not isochronous. CDC implies control, interrupt and bulk transfers, HID only control and interrupt.
    ...
  7. Replies
    7
    Views
    314

    Closed: Re: HEI primary current duration

    No damage, but also no high voltage output. Primary fly-back voltage needs to go up to 600V for 50000V secondary.
  8. Closed: Re: Flyback SMPS power MOSFET getting hot? uc3843 pwm converter

    RCD snubber is the appropriate method to absorb primary overvoltage caused by transformer leakage inductance. You have to check the actual primary voltage and current waveforms, an additional RC...
  9. Replies
    6
    Views
    232

    Closed: Re: Data acquisition using PIC starter kit

    Think about an ADC with DMA support and USB high speed or 100 Mbit Ethernet interface. Suitable CPUs are e.g. PIC32 (new MZ family has USB HS) or ARM (e.g. STM32F4xx).
  10. Replies
    7
    Views
    314

    Closed: Re: HEI primary current duration

    Back emf is is causing the ignition spark (fly-back converter principle), you don't want to cut it.
  11. Replies
    3
    Views
    141

    Closed: Re: Phase Difference calculation in cadence.

    What's the actual problem? Verification of your "phase shifter" or designing a phase or flight time measurement system?

    Does your "phase shifter" produce frequency independent phase shift,...
  12. Closed: Re: Runtime of clock using alkaline D cells instead of AA batteries

    Doesn't this demand for a transformer supply with battery backup? The battery is only discharged during power failure then.
  13. Replies
    3
    Views
    119

    Closed: Re: Current rating of Thermostat

    Means 16A resistive, 4A inductive load.
  14. Replies
    4
    Views
    162

    Closed: Re: Relay selection for Ultrasonic signals

    I don't see a necessity to use GHz relays for 25 MHz signal. I would probably select a slightly bigger relays with higher contact breakdown voltage.

    - - - Updated - - -


    Impossible with...
  15. Replies
    3
    Views
    172

    Closed: Re: Lock -in Amplifier/ tuned amplifier in DSP

    You can design FIR filters in Matlab and import the filter coefficients to the Intel FIR compiler tool.

    Lock-in is a different approach involving all-digital PLL (NCO, phase detector, synchronous...
  16. Replies
    2
    Views
    120

    Closed: Re: SATA SSD connection tx to tx or rx?

    SATA A/B assignment on the M2 connector should be according to the usage with standard SATA connector.

    155609
  17. Replies
    36
    Views
    2,006

    Closed: Re: Single conductor inside hollow conductor

    If the measurements are correct, a large share of the primary current runs as magnetizing current into the transformer inductance. You only told about AMCC-100 core (an amorphous cut tape) but...
  18. Replies
    3
    Views
    149

    Closed: Re: Pulse distortion after amplification

    Good idea. I guess you have input or output AC coupling and the bias point is shifting when the input signal is rectified in saturated operation.
  19. Replies
    3
    Views
    219

    Closed: Re: How good is ultiboard?

    Firstly I'd like to hint to a sticky thread on top of this forum https://www.edaboard.com/showthread.php?18145-Stop-the-is-xxx-software-is-better-than-xxx-software-topicz

    It makes a necessary...
  20. Closed: Re: Power harvester evaluation board and antenna issues

    Are you serious? Using an amplifier with energy harvesting? Did you understand the basic idea?

    - - - Updated - - -

    Energy harvesting is intended to supply ultra low power systems from a power...
  21. Replies
    12
    Views
    460

    Closed: Re: Lets take a look on a linear amplifier

    There may be good reasons to implement a linear (class AB) amplifier for your purposes, I don't apply to decide yes or no.

    You have implicitly specified amplifier output voltage and current by...
  22. Closed: Re: In distributed amplifiers, is it total input capacitance of the gain stage or Cgs

    Seriously, does the discussion about terms help in any way to answer the original question?

    Does the term "artificial transmission line" clarify anything compared to "LC delay line" (my favorite...
  23. Replies
    56
    Views
    1,487

    Closed: Re: Extracting energy from gyroscope precession

    The swing example is inappropriate for the original gyroscope problem. Swing involves periodical transfer between potential and kinetic energy. Work is done by weight shift which dynamically changes...
  24. Replies
    1
    Views
    244

    Closed: Re: Adapter design for pressure sensor

    Doesn't sound bad in general, but some details aren't quite clear. Do you mind to share a CAD drawing of the intended sensor mount?
  25. Replies
    11
    Views
    281

    Closed: Re: Operational amplifier driving capability test

    The described setup (setting a fixed output voltage) doesn't fully test "driving capability", you want to evaluate the available output current over a defined output voltage range.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4