Search:

Type: Posts; User: FvM

Page 1 of 20 1 2 3 4

Search: Search took 0.21 seconds.

  1. Replies
    3
    Views
    191

    Closed: Re: Could this electric shower be lethal?

    Some interesting points characterizing the device are quoted below:

    The heater

    156144

    The "earthing" electrode below the shower head

    156145
  2. Closed: Re: Network analyzer calibration for RF test points

    What the intended accuracy (delay, Z0)? MS-156C itself has limited precision, see e.g. VSWR spec.

    Did you consider to make your own calibration kit?
  3. Replies
    5
    Views
    280

    Closed: Re: readback the firmware Cyclone IV

    I would expect EPCQ16 used as configuration device. You want to check if it's connected to the FPGA respectively.

    Setup the configuration memory as attached AS flash in programmer and performe...
  4. Closed: Re: What is the cutoff frequency of the capacitively loaded Transmission line

    If mtline is setup as an ideal 50 ohm transmission line, the answer is very simple and you should be able to derive it yourself. Just a first order low pass with tau = c*Z0/2.
  5. Replies
    9
    Views
    606

    Closed: Re: Rigid flex Cross section OrCAD PCB Designer

    Solder mask and -paste are linked to top and bottom copper layer. You can't place component pads at internal layers and get no auto generated solder mask and solder paste for this layers, unless the...
  6. Closed: Re: Voltage spikes on the Gate-source of upper H-Bridge MOSFETs (for LLC converter)

    We are curious to see the result of the common mode test suggested by Easy peasy.
  7. Replies
    9
    Views
    606

    Closed: Re: Rigid flex Cross section OrCAD PCB Designer

    I would expect common stencils for rigid and flex part. A support may be required for the flex part.

    Special problem is second printing pass. It may be difficult up to impossible, depending on...
  8. Closed: Re: A way to delay UART frame for approx. 200-300us.

    At which Baud rate?
  9. Closed: Re: Difference between two biquads shown in diagram

    You are right, I overlooked one short in the first circuit.

    The answer is, fully differential is only possible in the four block topology.
  10. Closed: Re: Difference between two biquads shown in diagram

    Both circuits implement different transfer functions. Why don't you calculate it?
  11. Replies
    1
    Views
    137

    Closed: Re: Need help for read hex code

    Like many other flash CPUs, the application program can be readout in-circuit by manufacturer provided ISP tool or by general purpose programmer off-circuit. But it's only possible if the flash...
  12. Replies
    6
    Views
    261

    Closed: Re: help please tosimulate this file

    What do you want to achieve? Quartus is a FPGA synthesis tool, not a simulator. You may use the free Altera Starter Edition of Modelsim shipped with Quartus 13.1

    To simulate the design, you need...
  13. Replies
    6
    Views
    365

    Closed: Re: ADC output bit rate and PCB layout

    475 MBPS SDR and 950 MBPS DDR, why not read the datasheet yourself?
  14. Replies
    3
    Views
    227

    Closed: Re: NPA 201 Absolute Pressure Sensor ODR help

    That's what I read into the datasheet. The specification is a bit vague, you may want to ask the manufacturer for an unequivocal spec or check the actual behavior yourself.
  15. [SOLVED]Closed: Re: NFC System with antenna which can provide from 1 A/m to 7.5 A/m signal strength

    1.5 to 7.5 A/m is the standard field strength according to ISO 14443 which has also been adapted for NFC, active mode. It can be achieved by most reader chips on the market without additional power...
  16. Replies
    5
    Views
    280

    Closed: Re: readback the firmware Cyclone IV

    The configuration has to be readback from the configuration device, not the FPGA.
  17. Replies
    3
    Views
    227

    Closed: Re: NPA 201 Absolute Pressure Sensor ODR help

    There's a minimum read time spec.
  18. Replies
    6
    Views
    365

    Closed: Re: ADC output bit rate and PCB layout

    Series 7 is specified for 950 MBPS DDR LVDS speed, 910 MBPS has little margin. It's suggested to use digital phase alignment to adjust the receiver timing.

    DCO and FCO must be sent to the FPGA...
  19. Replies
    7
    Views
    412

    [SOLVED]Closed: Re: Rookie making an audio step-up transformer

    Audio transformer needs to care for main inductance which forms a high pass with the load impedance. If you want e.g. < 30 Hz lower cut-off frequency, the primary main inductance Lh1 must be > 8...
  20. Closed: Re: Mains leaking currents causing problems in my house

    Removing Y capacitors can reduce ground leakage, but it doesn't change the fact, that a PC PSU isn't designed with reinforced insulation, thus ground faults can happen. Neither appliances like dish...
  21. Closed: Re: Which transformers can pass approvals testing rergarding isolation voltage testin

    With TIW used for secondary winding, the critical clearance is pin 9/10 to primary windings, including aux. Changing the secondary pins to 7/12 slightly increases the clearance. Or use additional...
  22. Closed: Re: Which transformers can pass approvals testing rergarding isolation voltage testin

    Unless you have additional spacers, the clearance between winding and SMD pin isn't larger than about 5 mm.
  23. Replies
    9
    Views
    606

    Closed: Re: Rigid flex Cross section OrCAD PCB Designer

    O.K., the coverlay and adhesive don't continue in the rigid part, but the flex substrate does. In so far your stack up looks better now. The stack up still doesn't look feasible at all. You have a...
  24. Replies
    7
    Views
    391

    Closed: Re: How to calculate transformer winding losses

    Did you try to detetmine the loss components yourself? The quoted statement can't be found in the datasheet. "Loss due to parasitic leakage inductance" doesn't sound like a serious substantiation. A...
  25. Replies
    7
    Views
    487

    Closed: Re: Voltage to frequency conversion using VFC32

    Why now? What did you change?


    µF? Really?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4