Search:

Type: Posts; User: KlausST

Page 1 of 20 1 2 3 4

Search: Search took 0.10 seconds.

  1. Closed: Re: how to select ac to dc adapter for a given device

    Hi,

    If your application needs 24V then your adapter needs to ouput 24V.
    --> adapter voltage rating needs to be 24V +/- some tolerance. (no 12V no 6V no other voltage)

    If your application draws...
  2. Closed: Re: A way to delay UART frame for approx. 200-300us.

    Hi,

    Form both of us, the lazy one is you. Every one can recognize this.

    You treat those who take effort to find a solution for your problem worse that the ones that donīt respond at all.
    Thus...
  3. Replies
    5
    Views
    278

    Closed: Re: readback the firmware Cyclone IV

    Hi,

    Sorry for my too fast answer.
    In our systems we use the SST25VF device as configuration device.

    But now I have to agree with FvM that for your FPGA the EPCQ16 may be the configuration...
  4. Closed: Re: A way to delay UART frame for approx. 200-300us.

    Hi

    You are upset because I donīt do your job - for free? Really?

    I took my spare time for you to find a solution, I did an internet search, I gave you a part number.
    I wrote more text than...
  5. Replies
    5
    Views
    278

    Closed: Re: readback the firmware Cyclone IV

    Hi,

    did you try to use an internet search before you ask?

    To make it short: Yes, the SPI serial flash is the configuration device.


    Klaus
  6. Closed: Re: FPGA program has some hard to trace glitches

    Hi,

    since an FPGA works as parallel machine there is no value like "workload". Either it is within timing specification or not. If it is within timing specifications, it should work.
    If it is...
  7. Closed: Re: A way to delay UART frame for approx. 200-300us.

    Hi,

    "Clock" is a rather common term in electronics, especially in digital electronics.
    It is mainly defined by the frequency and voltage levels.. (there are also more detailed timing parameters)...
  8. Closed: Re: A way to delay UART frame for approx. 200-300us.

    Hi,

    First try it on your own. Itīs rather sratight forward.
    Show us your result.

    Klaus
  9. Closed: Re: A way to delay UART frame for approx. 200-300us.

    Hi,

    out of curiosity I did a search:

    Now my solution is: an about 500kHz clock and MC14517 wired as 128bit shift register.
    It should work well for 9600 as well as 19200 baud.

    Klaus
  10. Closed: Re: A way to delay UART frame for approx. 200-300us.

    Hi,

    a 32kHz clock and an 8 bit shift register ser_in ser_out

    Klaus
  11. Closed: Re: How much does a solder stencil cost for a 160mm * 60mm PCB?

    Hi,

    Why not ask the stencil manufacturers?
    Or online calculators?
    Like this one: https://www.multi-circuit-boards.eu/en/index.html

    Klaus
  12. Replies
    4
    Views
    114

    Closed: Re: Current capacity of stranded 38 swg wire

    Hi,


    The forum is not meant to let others do your job.
    It's not more effort for you to do an internet search ... than for me.

    The benefit if you do the internet search on your own is:
    * you...
  13. Closed: Re: "Current" controle is a big issue using ClassD ?

    Hi,

    Could you please list all your requirements. Searching through a couple of posts/threads to find out what you want to achieve needs a lot of time.
    Voltage range, current range, frequency...
  14. Replies
    12
    Views
    830

    Closed: Re: Bridge diode thermal problem

    Hi,

    Since you are the designer - at least I guess so - you should draw the "suitable" schematic on your own ... within a simulation tool.
    Then run the simulation and check power dissipation.
    ...
  15. Replies
    4
    Views
    114

    Closed: Re: Current capacity of stranded 38 swg wire

    Hi,

    Why don't you use the countless tables that can be found in the internet?

    Klaus
  16. Replies
    5
    Views
    280

    Closed: Re: Printer Data Logger-Device

    Hi,

    Some printers have a "HEX out" mode, where you may debug the datastream.

    But expect a lot of data.
    Depending on what you print it may be a challenge.

    Klaus
  17. Closed: Re: Minimum switching current for Mechanical switch

    Hi,

    Where is the datasheet?

    Klaus
  18. Closed: Re: Minimum switching current for Mechanical switch

    Hi,

    You say it is 10mA "minimum" switching current. But you treat it as "maximum".
    I doubt that 10mA is the "maximum allowed" switching current - but it may be possible.

    Best if you post a...
  19. Replies
    6
    Views
    364

    Closed: Re: ADC output bit rate and PCB layout

    Hi,

    Since you have two data per clock period (one per edge): DCO of 455MHz gives 910MBPS.
    --> low margin.

    Klaus
  20. Replies
    13
    Views
    706

    Closed: Re: BLDC motor delta winding

    Hi,


    For sure.
    Your control unit is not able to decide whether the load is in delta or star connection (besides the magnitude of the current)

    Klaus
  21. Closed: Re: Passing both DC and pulses through a toroid?

    Hi,


    I know what you mean.

    Just to be more exact:
    * DC means infinite time.
    * If time is finite ... better talk about a "pulse"

    And even such a pulse needs to be a "single" pulse... at...
  22. Closed: Re: Passing both DC and pulses through a toroid?

    Hi,


    YES, but only theoretically with an infinite big core.
    NO, for real transformers.

    The bigger the core, the lower the frequency you may pass from primary to secondary.
    But low frequency...
  23. Closed: Re: Passing both DC and pulses through a toroid?

    Hi,

    I agree with asdf44.

    You have contradicting requirements:
    * applying DC
    * non saturating
    * no output

    If you apply DC... then there will be output.
  24. Replies
    6
    Views
    279

    Closed: Re: stm32f103 update frimware from spiflash

    ...sorry for the wrong order of posts
    ***************************

    Hi,

    Again: We donīt see your system. Please give usueful informations.

    Does your system support any other way (to...
  25. Replies
    6
    Views
    279

    Closed: Re: stm32f103 update frimware from spiflash

    Hi,

    Since we donīt know your circuit and your requirements ... we can only tell you the "usual" way.
    (And so do the internet documents)
    If your circuit or requirement differs from the usual...
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4