Search:

Type: Posts; User: baby_2

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    7
    Views
    364

    Closed: Re: Inrush current limiter

    Thank you very much for your comment.
    My PCB consists of a micro-controller and some optocoupler to enable and disable some 24V output switch (10mA). However, my main load is a motor driver which...
  2. Replies
    7
    Views
    364

    Closed: Re: Inrush current limiter

    Thanks for your comment and swift response.
    I put a power connector on my PCB. When I connect the power to it at first glance, because my Cap is empty, it produces a spark at my connector. In...
  3. Replies
    7
    Views
    364

    Closed: Inrush current limiter

    Hello,

    I have a 24V/6A dc power supply. When I apply this power supply to my circuit ( a diode bridge and 470MF capacitor) it produces sparks. I am going to use a NTC (about 10ohm). Based on my...
  4. Replies
    4
    Views
    253

    Closed: Re: EMC circuit protector

    Dear KlausST,

    Thank you for your comment and you useful info. I have heard that my PCB should be checked for EMI/EMC test which my board is not a high-frequency board it just has Ethernet...
  5. Replies
    4
    Views
    253

    Closed: EMC circuit protector

    Hello,
    I need to know how to protect my circuit from EMC test. My input voltage is 24V(3A) and after a pole diode( for preventing from reverse voltage) and TVS diode it goes to my regulator(MinMax...
  6. Closed: Re: Updating footprint in PCB window after being changed in PCB library

    Thank you for your comment, Yes I have checked but it doesn't work. I changed all of them by the mentioned way by wwfeldman.
  7. Closed: Re: A hole for Plastic pin of ethernet connector

    Thank you for your response. It means just by adjusting the hole size and disabling plated option ( even annual ring=0?) it works fine?
  8. Closed: A hole for Plastic pin of ethernet connector

    Hello,
    Here the ethernet connector(http://www.kosmodrom.com.ua/pdf/HR911105A.pdf) that I am going to implement in Altium.

    I need to know that for plastic connector (phi=3.25) if my configuration...
  9. Closed: Re: Updating footprint in PCB window after being changed in PCB library

    Thank you so much, it is somehow time-consuming because in my project that I have used multi-channel structure is so complex to do this procedure.
  10. Closed: Updating footprint in PCB window after being changed in PCB library

    Hello,

    I designed my board in Altium designer. After checking the DRC I had to change a clearance in my PCB library. Howeve after doing that, updating my schematic librar and schematic, there was...
  11. Closed: Changing room and component positions in Altium

    Hello,

    Here is my PCB file. I need to know why P1_1 and U2_1 don't move by changing their room position. In addition by selecting all components again, they don't move.(ROOM name :TCP1)

    Thank...
  12. Replies
    0
    Views
    200

    Closed: Altium limitation in PCB window

    Hello,
    I need to know why I can't move my cursor more than -180 on the x-axis? Altium 20.

    156433
  13. Closed: stm32f103c8t6 vs stm32f103cbt6 vs stm32f103c8t6 vs stm32f103re6

    Hello,
    I will appreciate if you could let me know the differences between stm32f103c8t6 vs stm32f103cbt6 vs stm32f103c8t6 vs stm32f103re6?
  14. Replies
    3
    Views
    695

    Closed: Re: HanRun RJ45 pins postition

    Thank you so much for your help. Could you help me to design dp83848I?(http://www.ti.com/lit/ds/symlink/dp83848c.pdf)
    In the datasheet it doesn't mention the value of these parameters directly....
  15. Replies
    3
    Views
    695

    Closed: HanRun RJ45 pins postition

    Hello,
    In this picture I can't find the X position of pins of 1,3,5,7. I will thankful if you could help me. HanRUn911105A
    155815
  16. Replies
    1
    Views
    256

    Closed: Help me to detect an IC in a circuit

    Hello,
    In an encoder I guess this highlighted IC damaged but I can't find its part number correctly to see its datasheet. I am grateful if you could help me.
    155795
  17. Replies
    1
    Views
    258

    Closed: Class B wave form problem

    Hello,
    I am going to see the output waveform of class B amplifier. First of all, I tested this circuit
    154995
    For low frequency (200Hz-200Khz) I see this waveform at the output.
    154996
    But by...
  18. Replies
    8
    Views
    533

    Closed: Re: Frequency Multipier in ADS

    Thank you, how did the 4th harmonic of (354Mhz) generate with that high amplitude? the frequency multiplier mentioned it has low harmonics and IM components.
  19. Replies
    8
    Views
    533

    Closed: Re: Frequency Multipier in ADS

    I changed and made my circuit bigger. Here is my present circuit (double mixer) (5X , 5X) I set my input frequency order in harmonic balance simulation about 150.
    154830
    As you can see in the first...
  20. Replies
    8
    Views
    533

    Closed: Re: Frequency Multipier in ADS

    Yes , you are right. I made a mistake not to take into account the "Input" and "Output" words.
  21. Replies
    8
    Views
    533

    Closed: Re: Frequency Multipier in ADS

    I really appreciate your help



    I created a Data items and add LHA-13HLN s-parameters touch stone so it doesn't have any supply voltage. However, I check the circuit by removing the...
  22. Replies
    8
    Views
    533

    Closed: Frequency Multipier in ADS

    Hello,
    I have designed and simulated a frequency multiplier in ADS but my result is not acceptable. My Frequency multiplier conversion loss is shown below.
    154764
    Here is my circuit.
    154765
    Here...
  23. Replies
    8
    Views
    930

    Closed: Re: Reliable GPS and Compass sensors

    Dear paulfjujo, I really appreciate your explanation.
    Some of my friends used Ublox GPS and they told me, in some situations they need more than 2 minutes to track the GPS satellites or need to...
  24. Replies
    8
    Views
    930

    Closed: Re: Reliable GPS and Compass sensors

    Thank you KlausSt,
    Yes you are right, but as you get familiar with different sensors by reading their datasheet you can make a good decision. I am grateful if anyone can help me.
  25. Replies
    8
    Views
    930

    Closed: Reliable GPS and Compass sensors

    Hello,
    I want to know what is the best and reliable GPS and compass sensors to connect to a micro-controller?

    Thanks
Results 1 to 25 of 107
Page 1 of 5 1 2 3 4