Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Help me choose a ESD protection circuit for this I/O signal

Status
Not open for further replies.

katrin

Full Member level 1
Joined
Dec 3, 2005
Messages
98
Helped
1
Reputation
2
Reaction score
1
Trophy points
1,288
Activity points
2,200
I want to use the ESD protection circuit(as shown below) for the I/O signal



could someone give me some suggestion?
 

Re: ESD protection for current mode input signal?

katrin said:
I want to use the ESD protection circuit(as shown below) for the I/O signal

But one input signal is just current mode signal, I am wondering for the ESD protection of current mode signal, is this circuit still applicable, because there will be a voltage drop on this series current limiting resistor

Or should I remove this series resistance for the current mode input signal?

could someone give me some suggestion? thanks

I believe you need some sort of 'bleeder' resistor (10M or so) to bleed off any static discharge to ground in case there is ESD present.
 

    katrin

    Points: 2
    Helpful Answer Positive Rating
ESD protection for current mode input signal?

you can search some paper about esd wrote by Albert Z.H.Wang
i think you will get what you wanted
 

    katrin

    Points: 2
    Helpful Answer Positive Rating
ESD protection for current mode input signal?

Secondary protection is normally only necessary when you need to protect the gate of an internal MOS. If your internal signal does not touch a gate but just sources/drains, then you should be o.k. without the secondary protection. I say this without knowing your exact ESD requirements or what kind of primary protection you have, so it's only a generalization where the primrary protection sufficiently protects your pin.

As far as your input current goes, if your circuit can live with the drop, then you don't need to remove it. You're actually in a better scenario having current mode input because the resistor will not affect your frequency response. In voltage mode the resistor limits the charging current, in current mode it does not. So if you can afford the voltage drop, keep the resistor.
 

    katrin

    Points: 2
    Helpful Answer Positive Rating
Re: ESD protection for current mode input signal?

For current mode input, I think your circuit input is source, am I right ?

If the circuit input is source, I suggest you can remove the resistor and secondly ESD protect. But you need to layout yout input circuits by ESD rules.

Yibin.
 

    katrin

    Points: 2
    Helpful Answer Positive Rating
ESD protection for current mode input signal?

for mm need second esd
 

    katrin

    Points: 2
    Helpful Answer Positive Rating
ESD protection

normally esd structure should be given in process manual. it needs to be proven in silicon by foundry, not by design
 

    katrin

    Points: 2
    Helpful Answer Positive Rating
Re: ESD protection

katrin said:
I want to use the ESD protection circuit(as shown below) for the I/O signal



could someone give me some suggestion?


where is the circuit??
 

ESD protection

katrin ,
there are two person major in ESD design in innios and taiwan , another person ,is called :
''Ming-Don Ker'', you can also search his paper o the internet. maybe it is more useful
 

    katrin

    Points: 2
    Helpful Answer Positive Rating
Re: ESD protection

Can you be more specific ? Layout can help quite a bit on ESD issue and it depends on your requirement.

For achieving CE standard ( 4KV contact descharge, 8KV air discharge ) with a relative good ic. It's simply by adding a cap to gnd with a inductor.( can achieve around 5.5KV contact discharge and around 10KV for air discharge ) A more expensive way to solve the problem is to use ESD suppressor.


Rogerynt
 

Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top