Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

connection of hall sensor to the dq

Status
Not open for further replies.
V

vamsee

Full Member level 1
Joined
Nov 6, 2012
Messages
95
Helped
1
Reputation
2
Reaction score
1
Trophy points
1,288
Activity points
1,885
hi all,

in my project I will be fixing the head of the hall sensor inside the tude and so only 3 pins are visible which has to be connected to the daq.

now my question is, how to connect these 3 pins to the daq?

**broken link removed**

kindly refer pg 8

thaq
 

Typical 3-pin hall sensor devices require a power-source : +V and GND.

The 3rd pin then gives an output which is a function of the applied magnetic field. The kind of output is defined by the actual sensor device you have selected.
So you need to tell us what that sensor's specs are ?
 

rohitkhanna said:
Typical 3-pin hall sensor devices require a power-source : +V and GND.

The 3rd pin then gives an output which is a function of the applied magnetic field. The kind of output is defined by the actual sensor device you have selected.
So you need to tell us what that sensor's specs are ?
Click to expand...

hi thanq very much for the reply..

I am using ratiometric honeywell hall sensor SS495A1 4.5 - 10.5 V/DC SIP..
**broken link removed**
 

Ok so specs are straightforward ...

Connect DC power source (Vs, GND) to pins V+ and V-. Unfortunately the specsheet I have doesn't show the pin placement, and you link didn't work.

The 3rd pin will be at Vs/2 for zero magnetic field, and it will vary by plus or minus 3.125mV/Gaus depending on direction of the applied field. This gives a full scale of ~670 G plus or minus above/ below the null gaus value.

Quite straightforward actually
 
  • Like
Reactions: vamsee

    V

    vamsee

    Points: 2
    Helpful Answer Positive Rating
rohitkhanna said:
Ok so specs are straightforward ...

Connect DC power source (Vs, GND) to pins V+ and V-. Unfortunately the specsheet I have doesn't show the pin placement, and you link didn't work.

The 3rd pin will be at Vs/2 for zero magnetic field, and it will vary by plus or minus 3.125mV/Gaus depending on direction of the applied field. This gives a full scale of ~670 G plus or minus above/ below the null gaus value.

Quite straightforward actually
Click to expand...
thanq for ur reply..
here is the sensor datasheet, pls find in the attachment..

U mean, shud i connect sensor with separate power supply or the sensor gets power from the DAQ itself?
 

Attachments

  • 505292-da-01-en-POSITIONSSENSOR_SS495A1.pdf
    1.1 MB · Views: 66

vamsee said:
... shud i connect sensor with separate power supply or the sensor gets power from the DAQ itself?
Click to expand...

As long as the GND is common to power supply & your DAQ, it doesn't matter where the V+ comes from.
I can see the package pinout now -- center pin is Gnd, left pin (facing the label side) is V+ and right pin is the output.

Rest is up to you. Take the plunge now, connect it and check now without asking further questions !!!!!!
 
Last edited:
  • Like
Reactions: vamsee

    V

    vamsee

    Points: 2
    Helpful Answer Positive Rating
Status
Not open for further replies.

Similar threads

Part and Inventory Search

Welcome to EDABoard.com

Sponsor

Back
Top