Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Recent content by zmanultra

  1. Z

    Nice I2C asembler routine for PIC16F84A needed

    i2c pic16f84 meppel i have programmed the exact same card b4... the steps to go on about it. for testing... (write a serial routine which just outputs a letter every second or somthing...(in pic basic pro its just 2 lines of code...check it out) and then get a software (google it up) to...
  2. Z

    Nice I2C asembler routine for PIC16F84A needed

    master i2c for pic16f690 dont worry about "gold wafer card" look at it as simply programming a chip....(pic16) have u programed that chip b4....if not, just have a look at the sample code provided (e.g. pic basic is good for beginers)
  3. Z

    Nice I2C asembler routine for PIC16F84A needed

    i2c with pic16f84a its like programming a normal pic processor....the only difference is that u must creat a serial Comm routine...check out picbasic pro...it has some serial routines...thats the easiest way....or u can use microchip compiler.... hope this helps :)
  4. Z

    How does 4 pole, triple throw switch work?

    4 pole, triple throw A.Anand thanx i understand now. i just needed time to sink in, i undestand 100% now :) i wasnt looking at the actuall outputs off e f g h... each set will give a different signal :D
  5. Z

    How does 4 pole, triple throw switch work?

    4 pole, triple throw you know where u said that either E(i),F(i),G(i),H(i) will have power or E(ii),F(ii),G(ii),H(ii) will have power .....does that depend on what i feed the inputs? and also, whats confusing me is the why the hell do e for example have two lines? can you explain that?
  6. Z

    How does 4 pole, triple throw switch work?

    Re: 4 pole, triple throw how does it work? say i want to the first mode to be off (no power) the second mode to have power (signal A) , and the third mode to have power (signal B) i dont know how to go on about it i drew a pic for you to help me understand what will happen. i really...
  7. Z

    How does 4 pole, triple throw switch work?

    Re: 4 pole, triple throw you said.... the 4 input terminals contain a different input each.... do you mean the 4 input terminals contain a different output each....
  8. Z

    How does 4 pole, triple throw switch work?

    Re: 4 pole, triple throw i dont understand what do you mean by : "4 inputs can be connected to 3 output sets of 4 poles each....." im so confused
  9. Z

    How does 4 pole, triple throw switch work?

    im really confused about the operation of these kind of switched i need to use one because the toggle allows the user to choose between 3 modes of operation. can some one explain the circuit for me, im i dont know how it works, i googled but didn’t help me... :cry:
  10. Z

    serial digital data network which 1

    im want to use the most fastest and most accurate digital data network? do you guys have any recommendations? like for example the CANbus or SPI or SMbus etc
  11. Z

    Motorola DSP56156 simular replacement

    the Motorola DSP56156 has been discontinued, and i need to replace it with something simular to it from the same family, i don’t know how to go on about it, please help me with some guide lines :cry: this website only contains a different family the DSP563XX but not DSP561XX i want to minimise...
  12. Z

    usb ethernet or serial

    hi guys, im a new engineer in search of some experienced suggestions in regards to communication methods selection, i need an opinion on choosing the most accurate (with least errors occurring) and fastest communication method. The board that im going to use has the following: Gigabit...
  13. Z

    CAN Bus Filter & Masks?

    cansetfilter hi there, i have 4 node, node A node B and node C and a master node alpha node alpha is the one that wants to recive messaged from NODE A and B only say for example NODE A has a msg id of 0x020 and NODE B has a msg id of 0x030 how do i make the master node only filter msgs...
  14. Z

    C18 and -pulse width modualtion-

    c18 + pwm hi everyone can someone please tell the steps that need to be taken to control a uni polar stepper motor, i want to control it by using pwm in C but i don’t know were start can someone please help me, please please :cry:
  15. Z

    reading stepper motor position

    hi im programming a unipolar stepper motor in c for the pic18 device, in full step mode. one task is to get the position of the stepper, and i just can’t seem to figure out a way to do it, can someone please help me on this, im in need of professional help from u guys. thanks in advance

Part and Inventory Search

Top