Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by zibby

  1. Z

    Looking for schematic for ICD2

    icd2br firmware Are you using registered version of Eagle PCB?
  2. Z

    Looking for schematic for ICD2

    icd2 schemat lvp Can you post/share your Eagle design files.
  3. Z

    Convert Protel99 to pdf

    protel 99 export pdf I don't have or use Protel. So that's why I asked someone to convert those files to pdf, so I can recreate them in EGALE PCB. I know how to make pdf files, but if I don't have Protel (99SE or DXP) than there is no way to open those files, isn't it. bitbaby, Please read...
  4. Z

    Convert Protel99 to pdf

    converting protel 99 files Can you convert the other file(s)? Thanks.
  5. Z

    Redesigning PCB for ProPic 2 Gold

    propic2 pcb As requested pdf files.
  6. Z

    Redesigning PCB for ProPic 2 Gold

    propic2 xp ok here's in double sided PCB with schematic and BOM (Eagle PCB format, v4.09) :D
  7. Z

    Convert Protel99 to pdf

    protel99se pcb to pdf file Hello, I know how to make pdf files (have distiller) but I don't have Protel I use Eagle PCB. Attached are files in protel Thanks.
  8. Z

    Convert Protel99 to pdf

    protel 99 I have some designs downloaded from Willem.org in protel format, and wonder if someone woulb be able to make them pdf files. It's few adapters for willem programmer (schematic and pcb) I'll upload files only if someone can convert it. Thanks for your help. Zibby.
  9. Z

    Redesigning PCB for ProPic 2 Gold

    propic ii I have hex for 12c508 and want to use it with this programmer. So because of that I want to make sure pin8 (db9) is connected to pin8 (db25) Thanks.
  10. Z

    Redesigning PCB for ProPic 2 Gold

    propic Ok, let me rephrase my question. Original ProPic2 (and all mods) are connected to parallel port (printer port, LTPx), not serial port (COMx). Original schematic is using DB9 connector, with cable DB9 to DB25. Original schematic has labels for DB9 and also parallel port DB25. E.g...
  11. Z

    Redesigning PCB for ProPic 2 Gold

    I'm redesigning PCB for ProPic 2 gold (once done I'll post it here, Eagle file) and I have few questions. Original schematic is using DB9 on PCB, and DB9-DB25 cable. I want to use DB25male connector instead, so I just want to make sure I have it right. I got all pins except the one from 12c505...
  12. Z

    MPLAB Compatible 8/18/28/40 Pin ZIFF+ ICSProgammer

    I'm looking for schematic for this programmer **broken link removed**
  13. Z

    MAKInterface schematic needed.

    makinterface schematic I'm looking for schematic for MAKInterface **broken link removed**
  14. Z

    Simple EPROM Programmer

    circuit for eprom programmer Shareware version is very limited (file size, etc..) Full version is $50, it's cheaper to buy programmer with software, than build it and but software separate. Attached is simple and "safe to use" EEPROM programmer (24x series only) It works with PonyProg.
  15. Z

    Virtual frequency meter (based on AT90S2313)

    measure frequency with at90s2313 rest of pic.
See more

Part and Inventory Search

Back
Top