Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
I have generated the greber files as you are told. but my problem is:
in the FAB Layer there are stack-up, drill table, drill guide, some texts
How should I show drill guide symbols on the PCB? as you see with some red symbols in the first pic.
Hello
I want to generate gerber files in Altium
I could placed drill table in drill drawing layer but how should I show drill guide like below?
actually I need it to generate a Fab Layer.
Thanks
Hello
after many days I haven't been able to find my problem!
I have sent you my project link, please check it and tell me what's my problem :)
Please
**broken link removed**
the Library I have used:
**broken link removed**
**broken link removed**
**broken link removed**
please draw a polygon on...
could you please tell me my problem?
after many days I'm very frustrated with ADS!
I have a very simple circuit:
then from Layout Menu> Generate/update Layout>
I have transferred it to a Layout (I have inserted a polygon and some vias)
polygon property that I have used:
via property...
Hello
I have drawn a 6-layers layout in ADS.
I should have a ground plane and many ground vias on the top layer.
I have inserted a ground plane with 20mils clearance as shown below:
some area should be ground free as you see with Red Cross in above pic. how should I draw a keep-out layer...
Dear
Yes, I think I should set something in schematic to set these components at top layer
I have opened an example from default path in ADS's folder:
C:\Program Files\Keysight\ADS2016_01\examples\Training\Layout
actually they have used symbols instead of prepared models (Design Kits) as shown...
OK :) Thanks
I have set a 6-layers substrate as shown below:
as you see I should mount the components on the top side (metal6) but when I want to transfer it to layout:
I want to route some tracks on the top side, but the components don't have some pads on the top side! I tried to change...
Hello
I have a differential filter that drawn as shown below in ADS schematic:
first of all I need to check the reflection coefficient of this filter.
second I need to check the insertion loss of the filter.
I have placed 4 ports in the schematic. Do you see any problem in my schematic...
I have downloaded some ADS libraries and unzipped it and checked the definition files.
then I drew a schematic as shown below:
but when I want to simulate it I see this error message:
what should I do?
I couldn't find well documented tutorials for ADS. most of Keysight's tutorials are...
Dear
Thanks
you mean I should use "lumped-components" in schematic instead of "Lumped-with Artworks"?
How should I attribute models?
I watched the below video before
https://www.youtube.com/watch?v=v0OMSx1vLnc
I did like him but there is no SMD models for Resistors, Capacitors, Inductors in ADS...
Hello
I have a passive filter with a 6-layers PCB.
this is the substrate:
I have drawn the schematic in ADS using Lumped-with Artwork and simulated it.
then using Generate/update Layout, I transferred it to a layout as shown below:
(plus I have used rectangular with 20 mils clearance)
but...
hello
i wanna make a portable device for real time fft and digital filters (such as NarrowBand,BroadBand filter) from 16bit sampled sound.
i need to low power chip.
it uses from 4.3 inch tft touch screen for display.
which one is better between cyclone FPGA and DSP(such as tms320... or omap...
hello
i wanna make a portable device battery powered for real time fft and digital filters.
i need to low power chip.
my device use from 4.3 inch tft touch screen for display.
tms320vc5509 is a good choice
cycloneIII better than from tms320vc5509?
please advice me.
thank you
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
