Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
try this for using step directive
https://www.analog.com/en/resources/technical-articles/ltspice-using-the-step-command-to-perform-repeated-analysis.html
.op sets the operating point
you have not directed spice to do any analysis
suggest you use step 1000 1600 100
this should give 6 steps...
not an expert in this subject, but:
it depends on what the component is made of and how much radiation it gets hit with
consider a thin film resistor - enough ionizing radiation can degrade its performance
perhaps also a thick film resistor
capacitors are two (or more) layers of a thin...
page 1 of the data sheet lists theta as operating temperature, -40 to 70 degrees C
the web page for said device https://www.hakel.com/en/product-hsa-275-detail-153948
has quick contact information with a phone number and an email address.
not quite sure what you are asking.
nor do i follow what you wrote.
6 ohm in parallel with 3 ohm yields 2 ohm
2 ohms in parallel with a 2A source is 4 V
Thevenin form is a 4V source with a 2 ohm series resistor
shorted yields the 2A from Norton version
you didn't say what format the 3D model is
this may help:
https://forums.autodesk.com/t5/fusion-360-electronics/how-to-add-3d-step-file-in-existing-pcb-library/m-p/9458768#M1316
the 4th post of 9 (Jorge Garcia) writes how to do it, but the instructions are a little short
this video should...
this looks like a homework problem
what does 7 segment display PCB mean?
when does the buzzer buzz?
you gave this title:
"Need to make a up down counter from 40-00 and 00-40 without resting using two 74192 ic."
when started, does it count down from 40 to 00, then automatically count up from...
I'm not an exert on level shifters, however, I will state what seems obvious:
the level shifter has to go between the low and high levels, with the
zener diode / transistor / resistor that accomplishes the level shift
placed between the low and high levels.
i'm not sure what you mean by "be...
what frequency?
you can detect a zero crossing, then wait ??? us so you can be 430us +/-50us before the next one
clearly the synchronization has to take place before you try doing whatever you want to do 430 us early
+/- 50 us is a large tolerance
50 Hz means a zero crossing every 10 ms -...
i do not really understand your issue, but my daughter had some issues, that eventually were diagnosed.
she has learned how best to deal with it. in the process, we did a lot of grasping at straws.
if you will allow me, i'm going to grasp at straws
you exchanged the tv for a new one 17...
the magnetic field inside the torroidal core is essentially confined to the core.
there is some leakage of field lines, but it is minimal.
now you put it another coil around the same core and rotate the original
if the current in the original coil is DC, the flux is constant and you'll get...
you wrote that your instructors results do not add up to the equation
show what doesn't add up
as i read the problem, there are 5 unknowns
you need 5 equations to solve for the 5 unknowns
and you need to grind through the algebra carefully
as a side comment, most homework problems are set...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.