Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Hi Guys,
Do you guys know any Android book that got included the tutorial for bluetooth development ( Receive & Send Data)? I need it for interface between android with my PIC18F microcontroller.I already create the basic turn on/off and write/send bluetooth using eclipse but i wish to know...
Hi Guys,
i followed the instruction from Arduino HC06. I can use serial port ( Com 3 ) to turn on & off the LED by sending the command f or n at Arduino Leonardo as what he did. But when i connect the HC06 with my TeraTerm ( Bluetooth Terminal ) , it unable to type any command in it after...
Hi guys,
As i know, HC05 can use as master and slave mode,Whereas the HC06 only can use as slave mode. Currently, i having the HC06 and doing the bluetooth connection between arduino and android device. The HC06 slave mode will affect the send/receive data from arduino? I not really...
Hi Udayan92,
My problem now is able to display on LCD, but cannot display data into the PHP Website Textbox.
Something like : <input type="text" name="Temperature"
hi guys,
I want to know the way to transfer the temperature sensor data from arduino and send it to my PHP website textbox. I had successful get the temperature from the arduino and display at LCD. And I using HC-06 module as my bluetooth connection between arduino and my laptop. Please help...
Borber
I tried the way like that before, it's works fine. But is it an ideal way ?
crutschow
i tried to connect it directly from 9V adapter, it's works fine with the output around 3V.
Hi Guys,
i started to build my own voltage regulator with difference voltage as 9V,6V,5V and 3V.
So, I have one 9V adapter and connected it to the 7806 voltage regulator which gets the output 6V. From the output of 7806, i connect it to the 7805 Voltage regulator which gets the output 5V...
Hi Guys,
I wanna build a circuit with different output voltage from 12V->9V->6V->5V. When i build the circuit like 7809 voltage regulator, it require 3 capacitor to get 9V output. After i get the 9V output, was it necessary to build a 6V output with 7806 and 2 capacitor or without capacitor...
I mean the Reference voltage remain 1.25V even i change the input from 6V to 12V ?
And 1 more thing is the R2 got specific value, example: 10k,20k or 100k ohm ?
Hi guys,
Normally my friend will use ripup and route to connect those error line after the autorouting for reducing the error after DRC.
Is there any easier way than the manual routing? Thanks
Regards,
YY
Hi guys,
i have some doubt for the LM317 voltage regulator. According to the link below, it's say the reference voltage=1.25V.
1) Where did the 1.25V comes from?
2) Changing the value of the Variable Resistor ( R2 ) can get difference value of output?
3) The formula shown in the picture can...
Hi guys,
i had connect the circuit as the picture, but i connect the RA0 with a infrared receiver ,and the RD7 for the Infrared transmitter and all the each PORTB has one led. I put the infrared very close to each other, it still nothing happen. My programming got error? Please help. Thanks...
Hi,
Actually i want to do something like this video. But i wondering how the brush mount with the motor, So that it can spin in circle and send the dirt to the vacuum cleaner at the middle. Actually the thing is called as brush right?
https://www.youtube.com/watch?v=x_wuV7skV7U
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.