Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
I saved real voltage output data from the impedance analyzer as a CVS excel file and then, I usually put real data using VPWL_FILE source from the Pspice simulation. So, I could use the voltage source with real voltage signals and simulated some simple design together.
From ADS, I found VtPWL...
High Voltage TSMC 0.18 design kit for ADS 2005
I am looking for High voltage TSMC 0.18 um design kit which can be used for ADS 2005.
It would be really appreciated if you have that. My e-mail is whitecoven@hotmail.com.
Thanks in advance
Chris
I have simulation impedance data file which is text or excel(csv) format. And, then, I will import these file into Agilent ADS program and then, plot it with a separate graph to compare with another simulation plot of my designed circuit together. So, I can compare how similar two graph is...
I have got PMBD7000 (3 pin diode) Pspice model from NXP Semiconductor web-site. This model contains 2 diodes and 3 pins in the diagram
After automatic converting the spice file of PMBD7000(Lib->OLB) using Pspice model editor and put the library in the OrCAD Capture window, only 2 pin symbols are...
If we need to measure rise/fall or pulse width of device, we need to apply square or pulse wave from function generator.
Can I use 1 cycle square or pulse wave instead of continuous(CW) 1 tone wave from function generator ?
I want to get the pulse width(50%) of the diode limiting devices.
I am using Pspice Capture(schematic) so I had better use PWL source instead of ETABLE under ABM library. When I found ETABLE from OrCAD PSPICE User Guide, I must manipulate the source in Spice code.
Anyway, thanks for your explanation.
Added after 9 minutes:
Thanks for your description. I...
Thanks for your reply.
That means I need to put the data one by one. Is that right ?
My data in excel file has around 1000 lines so I am wondering it is a kind of way to read the input data directly without putting the value.
I am designing the simple operational amplifier and I need to use and simulate the input from the experiment data of the Oscilloscope. And I want to check how much opamp will amplify this experiment data. The waveform is a kind of arbitrary waveform from oscilloscope.
Is there any ways to use...
For 100MHz low noise preamplifier design on the breadboard, the load inductor is
around 1.2uH for my design. I want to show the bandwidth between 70MHz and
130MHz for this amplifier.
Should I consider the SRF(Series resonant frequency) for bandwidth ?
Or care about center frequency (100MHz)...
Re: which opamp is good for 100MHz high pass sallen key filt
As far as I know, slew rate is proportional to bandwidth. So high slew rate can satisfy the broad bandwidth. How much is good slew rate for this kind of high pass filter ?
Thank you for your answer and your comment is really...
Re: which opamp is good for 100MHz high pass sallen key filt
Thank you for your answer.
Is this Opamp(AD8039) library which I can use in PSPICE 9.1 or Agilent ADS 2005A software ? I can not find this opamp in the library of PSPICE or ADS.
Your help is much appreciated if you recommend if...
Re: which opamp is good for 100MHz high pass sallen key filt
I think the cut-off frequency need to decreased to at least 10MHz because the output should filter out in the low frequency and then, I need to find the wideband opamp.
Thank you so much for your answer
Added after 1 minutes:
I...
related:www.national.com/an/oa/oa-26.pdf
I need to design 2nd order 100MHz sallen key filter and looking for good opamp.
The cut-off frequency of the filter is 100MHz. I used LM324 opamp but this kills the
gain before 100MHz. My simulator is PSPICE and they have lots of library.
Could you...
From your answer, the filter can not help the preamplifier to get output with this kind of specification. Is that right ? I am also confused about the concept so I am asking the question here.
I guess the bandwidth of the Ultra wide band amplifier is 2 or 3 times bigger than center frequency. I...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
