Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by vmaxusb

  1. V

    comparing two Images in matlab

    comparing two images in matlab Hello, I want to compare two Images in MATLAB. Can any one tell me how can I compare Images in Matlab?... Thanks In advance..... ------------- Thank you.... vmax.
  2. V

    digital camera module and microcontroller

    camera module for microcontrollers I want to use Ethernet Controller RTL8019AS. And i am going to Interface It with P89V51RD2 microcontroller. is it Possible to Interface any camera module with P89V51RD2 Microcontroller? One more question appart: Can any one Provide me Internal Circuit diagram...
  3. V

    digital camera module and microcontroller

    microcontroller camera I am also looking for such application. If you find any Information related to this project please inform mr by sending PM. --------------- Thank You... vmax.
  4. V

    Ethernet controller RTL8019AS For camera.

    Hello, I want to make an application for monitoring camera through ethernet. I have Ethernet connectivity module for RTL8019AS. I want to interface camera with RTL8019AS module.So that I can monitor video thruogh ethernet. I don't know I should use IP camera or normal digital camera. And I...
  5. V

    Ethernet controller RTL8019AS For camera.

    Hello, I want to make an application for monitoring camera through ethernet. I have Ethernet connectivity module for RTL8019AS. I want to interface camera with RTL8019AS module.So that I can monitor video thruogh ethernet. I don't know I should use IP camera or normal digital camera. And I am...
  6. V

    Controlling stepper motor with parallel port

    stepper vb By using user port you can send the data to parallel port in windows Xp(only 32 bit). I have done that And I have Controlled stepper motor also. Thank You... vmax
  7. V

    Controlling stepper motor with parallel port

    control 2 stepper motor with parallel port you can send the data to parallel port by doing a programming in Turbo C also. But You can't send if you are Using Windows Xp x64 edition. you can use Windows Xp x32 edition to send the data to parallel port. There are Commands for sending the data to...
  8. V

    pc interface microcontroller using vb

    There is a good explaination of project for pc interface microcontroller using vb. **broken link removed** Thank You.... vmax
  9. V

    Serial Communication For P89V51RD2

    Hello, I am using the Microcontroller P89V51RD2. I want to Communicate it wth serial port. How can I communicate with it. I just want to On and Off the 7 LEDs from the Serial port. What would be the Programming at PC side if I want to Implement the Code in Turbo C. And What will be the...
  10. V

    Suggest me a board for using TCP/IP with embedded system in C

    TCP/IP + Embedded you can Use the board with ENC28J60 ethernet Controller If you are want to use PIC microcontroller. It is available on the following link. https://www.olimex.com/dev/index.html Check there are two to three boards for Ethernet controller. Thank You.... vmax
  11. V

    P89V51RD2 programmer Circuit

    flashmagic software for p89v51rd2 Hello, I have implemented all the Circuit. And now I am getting all the things right and I have programmed the MCU P89V51RD2 succesfully. Thank You very much for all your support. vmax
  12. V

    P89V51RD2 programmer Circuit

    programmer for p89v51rd2 Thank You very much for your reply and suggestions. I am impementing that circuit. -------------- Thank You... vmax Added after 1 minutes: I have implenented that Circuit diagram. The reset window is appearing.it is not get vanished. For how much time Reset...
  13. V

    usb beginner question

    cp2102 vhdl If You use PIC18F4550, there is direct Connection to USB. And you don't need any other MCU. It is itself Microcontroller. ------------- Thank You.. vmax
  14. V

    P89V51RD2 programmer Circuit

    89v51rd2 isp I have seen that forum. I think there are problems with Reseting the device. Also, There is not any connection for PSEN. Can You Give me Circuit diagram with some Description..? -------------- Thank You... vmax
  15. V

    usb beginner question

    vhdl cy7c68013 No, Have You seen the datasheet of PIC18F4550..? It has a D+ & D- pins available For Communicating Through USB. Which project baord You are going to use? What is application? ----------- vmax
See more

Part and Inventory Search

Back
Top