Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by tauseefrehman

  1. T

    [AVR] Programming Atmega328P with Arduino uno

    Hi, i have a question that can i program Atmega328p with arduino uno by just replacing it with its default chip and uploading the sketch to it and then putting it back to my own circuit. for example interfacing LCD with Atmega328p in 4 bit mode. or in other words if i compile a sketch for...
  2. T

    [AVR] Help on LCD 16x2 interfacing for AVR microcontroller

    @milan.rajik i am using AVR Studio 5 - - - Updated - - - @arun_190175 thank you for your response but understanding assembly language is very difficult for me at this moment. C will be better because its easy to understand. if you can help me with a C code that would be very helpful.
  3. T

    [AVR] Help on LCD 16x2 interfacing for AVR microcontroller

    Hi, i am trying to interface 16x2 lcd with avr microcontroller. i am new to c language and avr as well. although i am familiar with PIC and C++.
  4. T

    how to control dc motor speed using PID controller in simulink

    thanks SunnySkyguy. but in the case where the DC motor block has been used is not actually controlled but just driving it. although it helped me alot. i want to ask other thing, that why there is been an inertia block is been connected to the dc motor where as it has inertia parameter build-in...
  5. T

    how to control dc motor speed using PID controller in simulink

    hi, i am working on dc motor speed control in simulink. but i don't know really much about simulink due to which i am facing problem how to use the dc motor in simulink or how to operate it. thanks in advance
  6. T

    analog control of dc motor with pid controller for speed con

    hi, i am also working on dc motor speed control using op-amp. but i need to implement it in simulink, but the problem i am facing is that i can not connect anything to the armature input of the dc motor.
  7. T

    Problem using memroy block in Proteus

    I have been using 27C256 (EPROM) which has the option of putting a .bin , .hex file which is already been programmed. But the problem is how to build .hex or .bin file. I tryed a Microntroller program's hex file. That was good but unfortunatly i Don't know the what that code has or how to change...
  8. T

    Problem using memroy block in Proteus

    Hi i have problem using memory blocks in proteus under memory ICs section. When I try to simulate it, it shows error "No pakage is selected".
  9. T

    [SOLVED] Can't find logic switches in proteus library?

    Hi, my name is tauseef ur rehman and I have question. I can't find digital logic switches in proteus library. I am using Proteus 7.10 SP2. Thanks
  10. T

    8 bit microprocessor project

    thanks noureddine1
  11. T

    8 bit microprocessor project

    thanks noureddine1. but i need 8 bit whereas it is 4 bit. - - - Updated - - - i have been asked to do it on a software like simulating it on software like proteus or any other.
  12. T

    8 bit microprocessor project

    Sorry but I have to ask you that what these things mean. Our teacher did taught us about microprocessor but didn't ever mention these words. so if you can explain them. thanks
  13. T

    8 bit microprocessor project

    Hi, my name is tauseef and i have been asked to submit proposal for 8 bit microprocessor. Basically i have been asked to design an 8 bit microprocessor which should perform some basic operation like add, subtract, compare etc. I googled but didn't work. I am confused :-? that how to design it or...
  14. T

    [SOLVED] Best and easy software for PCB routing schematic layouts?

    Thank you very much - - - Updated - - - thanks keith
  15. T

    [SOLVED] Best and easy software for PCB routing schematic layouts?

    Hi evry1 I need to know the best software for pcb layouts. I have used Proteus and understand it but its not that much good for PCB layouts. The reason i guess is that its routing paths are very narrow. Than after echting it on board it becomes more narrow. Thanks in Advance.
See more

Part and Inventory Search

Back
Top