Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by ss_engg

  1. S

    Generator impedance affect the fault current

    My question is related to system Protection and it is: "Generator impedance doe snot affect the fault current to a great extent in low-voltage distribution system. Explain? I need the answer of this question. kindly help
  2. S

    sample question how to design an common emitter and common base amplifier

    I would like to design a question based on common emmiter and common base amplifier. Anyone who have a solved question regarding to these topic.
  3. S

    How to find Internal source resistance practically

    I would like to perform and experiment in which i want to measure internal source resistance of function generator (as you can say to verify the internal source resistance of function generator is 50 ohm) so i can perform it on bread board.
  4. S

    16 bit Barrel shifter question for paper

    I would like to give a question regarding to barrel 16 shifter in paper its code should be in VHDL. kindly anyone help me to provide me a question and its solution.. I'm new in VHDL language.
  5. S

    VHDL Program for a 4 bit full-adder

    when I put the values in test bench then it cause error. then how we put the values in test bench file
  6. S

    VHDL Program for a 4 bit full-adder

    may you please mention that how to assign input values of 4 bit adder in vhdl.. is it like that a<= '0000'; or in another formet.
  7. S

    4 to 20mA circuit design

    in my assignment it a condition to use 24vdc and variable resistor. so in your diagram 10vdc is supply is it possible with 24vdc.?? and I measure the current levels like 4-8-12-16-20mA from emitter to ground ?? Am i right ??
  8. S

    4 to 20mA circuit design

    BradtheRad < kindly do tell me transistor name as well as from which point of transistor I collect the require current levels >
  9. S

    4 to 20mA circuit design

    I have a picture capture from internet regarding to 4-20mA current circuit.. kindly open this close picture.. and guide me ... - - - Updated - - - the problem is that when I apply this circuit then not get a linear relation e.g at Minimum value of resistance 20mA and at high value its 4mA but...
  10. S

    4 to 20mA circuit design

    I would like to design a circuit of 4-20mA( which is most common circuit in industry application) with variable resistance... selection of variable resistance is like that at Max resistance the current should be 4mA and when Mini resistance then the current should be 20mA. How I design this...
  11. S

    4 to 20mA circuit design

    means at minimun value of resistance its 20mA and then gradually with 25% of that selected resistance the current should be 16mA and so on. the supply voltage should be 24 volts.. kindly help it .. schematic diagram or that circuit
  12. S

    4 to 20mA circuit design

    Hi, I would like to design a circuit that give me 4-20mA current using variable resistance. There are following requirments: 0% resistance 20mA 25% resistance 16mA 50% resistance 12mA 75% resistance 8mA 100% resistance 4mA kindly help me out to design this circuit Thankyou
  13. S

    what is basically an inductor

    I still not get the main reason why we twist the wire.. pleaase elaborate it more.. i shall be thankful to you...
  14. S

    what is basically an inductor

    what is the main logic behind twisting the coil ?
  15. S

    what is basically an inductor

    What is inductor basically means if we untwist that coil and make it straight wire still it will be called inductor.. ?? kindly response me ... Thankyou
See more

Part and Inventory Search

Back
Top