Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
Hi Viper,
Consider the case of current mirror (One MOS diode connected, providing VGS to other MOS), in reference branch the reference current is say 1uA. than what will be its overdrive voltage (Say Vth=600mV).
Here we need to know what is W,l of MOSFET.
Say for a particular W,L if...
I got answers up-to some extent, sharing for others.
1. PFM mode loop is open loop or close loop?
Ans: Close Loop.
2. Can we model the PFM loop?
Ans: Yes, we can model the PFM loop using state-space averging method. Its bit complex as involved algebra.
3. Is it required to do Stability...
I didn't get your point. "System is not present" means what ?
PFM loop consist of: Res div feedback, Max current detect block, Zero current detect block, Comparators along with PowerFets, L & C etc.
Please Consider PFM loop as closed loop. Correct me if I am wrong.
Please explain in terms of stability analysis. That will be helpful .
- - - Updated - - -
Yes, for PWM mode Stability analysis is required. Please explain the necessity of stability analysis in PFM loop.
Re: What will be the Gm, Rout & Av= Gm * Rout of a single-stage Common Drain amplifie
Okay Lvw,
I will think on your comments (should give some time on CD stage).
Thanks for your time and consideration.
Re: What will be the Gm, Rout & Av= Gm * Rout of a single-stage Common Drain amplifie
Hi LvW,
Yes, certainly I am missing some point about CD stage amplr. That`s why I am discussing it here.
Thanks for being patience with my doubts.
So now for CD stage if you are Saying...
Re: What will be the Gm, Rout & Av= Gm * Rout of a single-stage Common Drain amplifie
Hi LvW,
So In case of CS stage Av= Gm * rout Is it correct ??? If yes then
Av = gm1 * (r,load||ro1); with r,load=ro2 we have Av=gm1*ro/2
Here my point is : rout = (ro2||ro1), is used in gain...
Re: What will be the Gm, Rout & Av= Gm * Rout of a single-stage Common Drain amplifie
Hi LvW,
Thanks for your explanation.
Considering your answer "Av=Gm*Rs" is correct. I am getting one more doubt. So I would like to ask same question in terms of CS stage amplifier with pmos...
Re: What will be the Gm, Rout & Av= Gm * Rout of a single-stage Common Drain amplifie
Yes, So can I say
if r,out=Rs||(1/gm) & Gm = gm/(1+gm*Rs)
Then Gain Av= Gm*r,out
Av = gm/(1+gm*Rs) * Rs||(1/gm) = gm/(1+gm*Rs) * Rs/(1+gm*Rs) = ( gm*Rs)/(1+gm*Rs)^2
But CD stage Gain...
Re: What will be the Gm, Rout & Av= Gm * Rout of a single-stage Common Drain amplifie
Hi LvW,
Please specify the Gm & Rout in the gain formula.
Are you saying Rout = Rs || (1/gm) = Rs /(1+gm*Rs) is not correct ??
& Gm = (gm)/(1+gm*Rs) is correct ?
Please reply.
What will be the Gm, Rout & Av= Gm * Rout of a single-stage Common Drain amplifier
Hi All,
What will be the expression of Gm, Rout & Av= Gm * Rout of a single-stage Common Drain amplifier.
Here Gm is trans-conductance of the amplifier.
If over all gain Av = (gm * Rs ) /(1+gm*Rs) &...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.
