Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.
I am going to replace it just to be sure it's not the culprit, tomorrow i will buy the parts i need i will be buying a "100v 47uf eletrolytic" and that "b 101k 2kv" thanks for the attention peace i will update as soon as i install the new caps :thumbsup:
Im Sure its going bad, if its not bad it will go bad soon, the readings oscilate a lot from 90 to 93/94 now, it can be the meter batery but i believe the capacitor is going bad or about to hints, cheers:thumbsup:
:bang: I forgot to mention: The readings are oscillating a lot from 91 to 91.1/91.2/91.3/92 sometimes 95 its bad right tell me this is the issue im losing hope :shock:
It's a B-101k 2kv capacitor i took it out of circuit right now, B stands for +0.1Pf and the meter values are 91.3 pf, i think its bad ? +0.1pf tolerance ? :bang:
Hello again, after some time away from home i finally got able to test the transformers and some other components, unfortunatelly all seems to be good. My last hope is a Ceramic Disk Capacitor a very small one right on the scan coil plugs on the "H. Section cables" i was measuring in circuit...
I will correctly measure the Horizontal output transformer "T401" and all its components and then i will give updates about the work. I really tought it could be the IC201 because i had no image at all only backlight, i touched it and the vertical became opened again, with that i decided to take...
Hey, i found no signals of arcing just heard the tickling noise, the new problem with the vertical was bad contact with the micom microship, as soon as i cleaned it the vertical opened again with no problems like the normal, I have only the horizontal issue for now. As i said, i changed to...
Hello again, after searching awhile i have discovered what might be the problem, and (im 90% sure its "an IC failure"), the big micom microship. I managed to find the right chassis model of the screen wich is here (**broken link removed**) after testing the microship the screen went all black...
Hello again, managed to test the whole yoke area but not the horizontal circuit, im having 2 problems now, one is cold solder joints somewhere i turn on the screen its all black with backlight, i touch the pcb it opens the vertical and stays like in the pictures, there are no damaged capacitors...
Only tomorrow i have the capacitance meter with me, i don't trust the tests with the multimeter, should i inspected those marked areas? That blue 2kv ceramic disk capacitor i never thought it could be the problem but who knows, another question (do i need to take out the capacitor to test it...
Brad! i had already tried to mess with the panel it opens but i can't see what im doing the image is all broken :/
betwixt i will dig in that .pdf today thanks for the quick tips in advance! :popcorn:
Thank you for the quick tips Brad!! I will check everything as soon as im able to in a few hours hopefully finding the culprit :grin:
- - - Updated - - -
:cry: Can't find any Schematic Diagram of this screen model (Samtron 96P), i have no idea were to look for those, i have a potentiometer...
Hello, my CRT Monitor from my old retro system currently gave up on me, after i tried to find what the problem was without success, i took the monitor to a specialist to check what the problem was to see if it could be fixed.
He said "there was no components to repair the damages", after...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.