Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Recent content by shanky07

  1. S

    [SOLVED] [Moved] Board for embedded linux.

    Thanks FenTrac !!!!! This is exactly what I was looking for. :) Thank You once again
  2. S

    [SOLVED] [Moved] Board for embedded linux.

    Hello Geeks, I have been working on controllers ,now want to work on embedded linux. Can anybody suggest me a board on which I can port linux and play with drivers. As my purpose is learning linux and drivers, I am looking for a board which will have interface like GPIO, USB, Display, Ethernet...
  3. S

    [ARM] Facing problem with lpc1752

    Hello Friends, I am working on a project in which I am interfacing few sensors with LPC1752. There are some debug prints in my code.. e.g initializing, then sensor data..etc I am using printf() function. The problem that I am facing here is,if I add some prints LPC1752 stops working..And I...
  4. S

    [SOLVED] Building ARM-NONE-EABI toolchain

    Hi roll no three thanks for the reply i am using ubuntu 12.04 i'll check whether it works for ubuntu and get back to you.
  5. S

    [SOLVED] Building ARM-NONE-EABI toolchain

    Hello Roll No Three I tried with --with-gmp ,--with-mpfr options but end up with error. please see the following link https://imvoid.wordpress.com/2013/05/01/building-the-gnu-arm-toolchain-for-bare-metal/ Here in Building the toolchain section- building gcc two commands are given I tried...
  6. S

    [SOLVED] Building ARM-NONE-EABI toolchain

    Hello Ricardo, Thank You for reply. I checked the link. I ll try building the toolchain. Is there any example code or some help for how to compile code for ARM?? Have you checked. I ll google it. But if you have any such material can you please share... Thanks in advance...
  7. S

    [SOLVED] Building ARM-NONE-EABI toolchain

    Hello I am trying to build arm-none-eabi tool chain to compile code for AEM7 lpc2148. I followed the steps mentioned on the following link https://imvoid.wordpress.com/2013/05/01/building-the-gnu-arm-toolchain-for-bare-metal/ But, when I entered ../../src/gcc-4.8.0/configure...
  8. S

    External Interrupt in LPC1114

    Hello friends, I am facing problem in external interrupt for lpc1114. Here is my code => void PIOINT0_IRQHandler(void) { uint32_t regVal; unsigned int i,j; gpioSetValue(0,2,0); for(i = 0 ;i < 500; i++) for(j = 0; j < 10000; j++); gpio0_counter++; regVal = gpioIntStatus(0, 1); if...
  9. S

    Compiling code for lpc2148 in gcc

    Dear friends Since long time I am working on ARM controllers and habitual with Keil software to compile the applications. But few months back I found that it is possible to compile the code for ARM in gcc with some toolchain. With the help of edabord I am able to build bare bord toolchain. But...
  10. S

    Compiling code for ARM in Ubuntu

    Dear friends Thanks for your help I have successfully installed the cross-compiler and gone through few basics of it. But I am still facing some problems in writing code for arm lpc2148 in linux is there any reference code or study material availbla from which i can clear my baisics and write a...
  11. S

    Compiling code for ARM in Ubuntu

    Thank You vinodstanur for reply When I post this thread i gooled and I found one link in which a command for installing cross compiler was mentioned. It was something like this sudo apt-get install gcc-arm-linux-gnueabi Is it the same that you are talking about ? I found this command on...
  12. S

    Compiling code for ARM in Ubuntu

    Hello friends I am working on LPC2148. I am trying to compile a code for LPC2148 in linux. I am using ubuntu 12.04.But as I am not much aware of linux I am unable to compile it. Do I need any extra toolchains to compile? if yes then which toolchain I should use? Is there any site where I can...

Part and Inventory Search

Top