Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Recent content by selva murugesan

  1. S

    About j1939/CAN protocol

    thanks to both of you what about the vector can oe simulation process?
  2. S

    About j1939/CAN protocol

    thanks horace1. It's only contain the historical data. But I need more about technical point of view.
  3. S

    About j1939/CAN protocol

    hi I am new to the j1939/ CAN high layer protocol. I am very much interest in to study about those. How can I get that materials? now I am using the vector canoe simulation software for checking the j1939. In that, lot of stuff available. I want to know full intro about the j1939 in vector...
  4. S

    Best book for knowing the RTOS in terms of programming

    Hi Please give some name of the books , which is easy to understand the RTOS from the basics I would appreciate if you are given some best website name of the best practice the RTOS programming Thanks selva
  5. S

    Motor selection for shaker project bio medical

    hi experts In my project , the requirements motor are ,which has forward reverse and one more thing vibration facility(12V,10 kg load).This project is mean by shaker (bio medical )
  6. S

    control strategy of Permanent magnet stepper motor

    Hi friends I want to know the way of control of PM DC stepper motor (12v).In both direction (rotation) and step by step.
  7. S

    How to check the crystal frequency?

    Yes.You can do it Disha. I used a 1x probe (cro) to measure it.Put one end into the Crystal pin.connect the GND pin into Ground connection.This is my personal experience. I might not see this procedure in any document.The result value is not show in fixed manner. It oscillating.But it shows...
  8. S

    Help Needed in the Motor selection process

    thanks.yogece Nope. I dont need the reciprocating movement.
  9. S

    Help Needed in the Motor selection process

    Hello experts I am in motor selection process.The project is Rotators. 24V, mininum tarque.Dc motor My motor requirements is simple , Motor should be rotates clock wise and counter clock wise direction. I think In any motor could do it.But additionally I want shake the motor shaft up an down...
  10. S

    How to check the crystal frequency?

    Thanks PA3040. But my question is , How to check the crystal,whether its working or not? before its soldered in the board.I am using PIC16F877A.
  11. S

    How to check the crystal frequency?

    Hi I want to Measure the crystal frequency.the crystal is in the microcontroller mother board.The micro controller is working properly. But I want to know to the way of checking the frequency.I used the CRO 1x probe , but it shows 50 Hz. but I know the crystal is 20Mhz. Any suggestion?
  12. S

    Problem in timer 1 in pic16f877A

    hi guys thanks. I try that
  13. S

    Problem in timer 1 in pic16f877A

    hi Kripton2035 thanks. I agree with you,now I made it with help of (20Mhz) main crystal.I want to change it into 32khz. can you Guide me for this?coding as well as harware(GND connection)?
  14. S

    Problem in timer 1 in pic16f877A

    thanks wp100, But ,I made it.first of all I used the timer1 for display the time. It is not delay (NOP) function. How can i turn off the timer 1 ISR.? I know that, disable the interrupt enable should be turn off the timer1. Is there any other way?
  15. S

    Problem in timer 1 in pic16f877A

    thanks Kripton2035 I would like to use the primary crystal (20Mhz) for timer1 base and micro-controller itself.Is that any problem

Part and Inventory Search

Back
Top