Continue to Site

Welcome to EDAboard.com

Welcome to our site! EDAboard.com is an international Electronics Discussion Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click here to register now.

Register Log in

Recent content by sekharece413

  1. S

    Need help to write code in MATLAB for CHIRP SLOPE KEYING MODULATION

    Dear sir/madam, I am working in implementation of chirp slope keying modulation and demodulation in MATLAB. Simulations that I completed are: 1. Chirp signal(up and down chirp) generation completed 2. Linear frequency modulation/chirp signal simulated 3. Random data...
  2. S

    Digital modulation technique - CSK

    Hi all friends.I hope someone can help me about chirp slope keying modulation( CSK) technique in underwater communications.I am working on CSK and need to simulate in MATLAB. Please is there anybody here to give me ebook or something else.(maybe documents..)about CHIRP SLOPE KEYING MODULATION...
  3. S

    Need MATLAB code for CHIRP SLOPE KEYING MODULATION

    Dear sir/madam, I am working in implementation of chirp slope keying modulation and demodulation in MATLAB. Simulations that completed are: 1. Chirp signal(up and down chirp) generation completed 2. LFM with...
  4. S

    interface between sparatan 6 xc75t ic and xc32p platform flash needed

    i need to interface between sparatan 6 xc75t fpga ic with platform flash xc32p i need cricut diagram and what are precondition to taken while interfacing
  5. S

    fpga interface with ddr2 sdram comptent

    hi,thanks for the reply, i know how use MIG, but i need interface between xillinx spartan 6 xcsl75tcsg484 ic and micron ddr2 ic of 512kB any design document or fpga design doc or board design document will help thanking you
  6. S

    fpga interface with ddr2 sdram comptent

    hi, i would like know how interface fpga spartan 6 lx75t with ddr2 interface ,how to design ?
  7. S

    do-254 certification for person

    hi, i am i am working in aerospace design company my company manger asked me to get do-254 certification(my self for project ) for my further project for designing and verification may know how get it
  8. S

    Job for IC Design Frontend(India)

    may be a m.tech might be helpful i hope so because vlsi industry needs master degree as mim
  9. S

    total ace extreme from ddc with pci connector

    can i interface total ace extreme ic directly with PCI connector with out any other bridge.
  10. S

    what happens 1553 bus controller fails and what is the soultion

    what happens 1553 bus controller fails and what is the soultion
  11. S

    How to implement 1553 bus in fpga..i mean what are requirements for implementation

    thanks and one more dout i have how TRANSCEIVERS of 1553 are interface with an fpga and what would be output of TRANSCEIVERS
  12. S

    How to implement 1553 bus in fpga..i mean what are requirements for implementation

    HI, i am new with fpga design and i would like know what are things need to implement 1553 bus on fpga , like what fpga ic should i choose or what fpga board kit should i need to achive 1553 bus functionality and how to design in briefly explication would help me .... thanks in advance for...
  13. S

    Importing of DXF file into allegro

    Thank you. I just start drawing a new Layout with reference to the actual one and with my designers input
  14. S

    Importing of DXF file into allegro

    Actually its confidential. but thanks for your kind attention about my posting. come to the problem the 0603 pin which I measured in the DXF is 26X40 mils but according to standards its 39X40 mils. May be the designers may alter the dimensions according to them. once again I am Thanking you...
  15. S

    Importing of DXF file into allegro

    Actually the DXF units are in inches. I modified the units I am able to get the PCB but when I am tryaing to place my circuit components on the layout I found that the dimensions are not matching except the one. For your understanding, one of the capacitor in the circuit given in the...
See more

Part and Inventory Search

Back
Top